 | | further observations on rotation sensor problem
|
|
It would appear that all movements (even when things are otherwise behaving poorly) are properly processed if the movements are done manually while the robot is doing it's computational phase. It would appear that things are dropped when the robot (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | rotation sensor problem (different one this time)
|
|
This occurs very irregularly, so I'm not sure what the problem could be, but it is a whopper. After a certain amount of time running my program, (or perhaps after certain inputs-I'm not sure) it would appear that ROTATION_X stops being updated. (...) (24 years ago, 27-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: light sensor problem?
|
|
(...) I remember wondering what port 6 bit 3 did and so I think I tried setting it on and off and not noticing anything broken either way. Maybe I didn't test enough though. Somebody might want to try repeating the experiment. Some extra evidence is (...) (24 years ago, 26-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RF Connection To RCX
|
|
One way to accomplish this is to use wireless serial devices. These RF devices allows one to hook up ANY serial device wireless. I have seen some listed on ebay for about $100+. The setup is as follows: PC--> serial transmitter serial receiver-->IR (...) (24 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
| | Re: RF Connection To RCX
|
|
Hi We just got into RCX. We have been using my Palm III and Visor to control the RCX. We have this great idea but need some help. We have an old Logitech Trackman remote control mouse. It uses RF. The idea is to some how convert the Serial output (...) (24 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
| | Re: RF Connection To RCX
|
|
Hi We just got into RCX. We have been using my Palm III and Visor to control the RCX. We have this great idea but need some help. We have an old Logitech Trackman remote control mouse. It uses RF. The idea is to some how convert the Serial output (...) (24 years ago, 26-Jul-00, to lugnet.robotics.rcx)
|
| |
| | Re: light sensor problem?
|
|
(...) I supposed so, but only to get a "fast scaling"? (...) I can "rescale" those values by theoretical calculation and maintain >>7 or make the right conversion (0-100). Now I've done the right scaling (ready to commit), but I sincerely think that (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | RE: light sensor problem?
|
|
(...) And I'll add the reminder (for all the newbies) that without Kekoa's efforts in doing the low-level documentation, we would not be where we are today.... Thanks again, Kekoa....... As a side note, I wonder how the power to the LCD controller (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: light sensor problem?
|
|
(...) I personally forget the numbers of the lugnet posts. The gist is that the firmware and LegOS were, at the time, different in a critical way. I don't know the current status of LegOS. At the time, LegOS cycled through the 4 A/D sensors, reading (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Rotation Sensor Values
|
|
This is the whole directory command dump. These errors are half-corrected if I specify ../include/*.h in the include# line. Then I get errors about not being able to find other *.h's that the originals included. Makefile:41: .depend: No such file or (...) (24 years ago, 25-Jul-00, to lugnet.robotics.rcx.legos)
|
