 | | Re: How do I test this thing?
|
|
Ross- My deepest apologies, but the HOWTO is sadly out of date- it refers to version 0.1.7 of the software, which is similar in many ways but drastically different in the makefile system. I'd suggest looking through the README file for better (...) (25 years ago, 1-Apr-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: NQC on Linux dilema...
|
|
(...) Ok, here it is: It just sits there, after sending about 5 lines of hex code to the RCX with that -v option. it will not send any more code after that, no matter how long you wait. I have not such thing as a PSerial_unix.cpp file does not (...) (25 years ago, 1-Apr-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC on Linux dilema...
|
|
(...) Does the program just hang, or does it eventually (several seconds later) give up and print an error message? Try 'verbose' mode and post the results: nqc -v -d test.nqc One possibility is that somehow the port is configured for hardware (...) (25 years ago, 1-Apr-00, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC on Linux dilema...
|
|
Hey, I have a little dilema when running nqc on RedHat 6.1 distribution of Linux on a Toshiba Satellite 2615DVD Laptop Computer. I have a 'winmodem' that workes on some port, and the IR transmitter on 'COM1' equivalent. It will not load the programs (...) (25 years ago, 1-Apr-00, to lugnet.robotics.rcx.nqc)
|
| |
| | How do I test this thing?
|
|
Hi, all. Well, just spent the best part of the morning downloading & compiling the h8300 cross-compiler. All worked perfectly, as per the instructions in the HOWTO. (I tried the binaries first, but was getting strange errors when I tried to compile (...) (25 years ago, 1-Apr-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: makelx issues
|
|
Kajim schrieb: (...) Depending on your configuration, there may or may not be certain error messages when building the compiler. They mostly deal with missing system libraries, which doesn't avail to much - legOS has its own libraries. (...) This (...) (25 years ago, 31-Mar-00, to lugnet.robotics.rcx.legos)
|
| |
| | makelx issues
|
|
Sorry to post configuration issues again; however, I have I beleive sucessfully compiled the new egcs 1.1.2[altho the self tests at the end fail...] and can begin to compile legOS 0.2.3 but makelx segfaults every time it is run... The only guess I (...) (25 years ago, 31-Mar-00, to lugnet.robotics.rcx.legos)
|
| |
| | controling two motors with only one output?
|
|
Hi guys, I was thinking about multiplexing motors, and it came to me that it should be easy to control two motors (only one at a time though) using one output of the RCX. Below, I describe my general idea, but I would like to know if you tackle this (...) (25 years ago, 31-Mar-00, to lugnet.robotics.rcx)
|
| |
| | Re: Modulo operator in NQC
|
|
(...) The limitation is more historical than anything else. Originally expressions were all evaluated at compile time, which is why I have a bunch of operators (%, >>, <<) that have no corresponding bytecodes in the firmware. Over the last few (...) (25 years ago, 31-Mar-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Problems reading active sensors with legos? Is there a solution?
|
|
I'm a bit confused with the reading of my light sensor with legOS. I'm getting values with a lot of "noise"... For example, reading the value for white, I'm getting values with a "noise" from 36 to 24 (raw) around the right value. Reading some post (...) (25 years ago, 30-Mar-00, to lugnet.robotics.rcx.legos)
|
