 | | External motor power and expansion board combo problem?
|
|
I wish to make the small mod to allow for external power to the motor outputs of the main board. However, this seems to cause several potential problems with the expansion board. First, the motor power connector is occupied by the motor power (...) (22 years ago, 30-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Why can't we manipulate TMSK1
|
|
Hello, We have some problems to manipulate TMSK1(address is 0x1022). We wrote the following test code: test.c ***...*** ***** void main() { int i, j; printf("\n"); i=peek(0x1022); printf("TMSK1=%d ", i); j=0x00; poke(0x1022, j); i=peek(0x1022); (...) (22 years ago, 29-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Interactive C Version 4 is available for free download
|
|
Hi! When I first fired up IC 4 it was wiithout the expansion board, and the HB booted fine. I suppose you could save some memory and processor time if you didn't load the expansion board libraries.) The list of files it downloads seem to be in (...) (22 years ago, 29-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Crispy Fried Sonar Board?
|
|
Yep I got this box of goods from Acroname, containing a sonar module and some servos. promptly tore it open, soldered the sonar jack to the board, and then apparently plugged the cable in backwards. When it didn't work, I put my hand on the sonar (...) (22 years ago, 29-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Help for measuring pulse width
|
|
Hello, We are trying to write the code to measure the pulse width which is less than 1ms. We use the input capture ports to generate the interrupts. We wrote the interrupt service subroutine by assembly language. But since this is the first time for (...) (22 years ago, 28-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Broken Charger/Interface board--last chapter
|
|
Well, it looks like reparing this charger/interface board is beyond me. I have now replaced all the capacitors, both 'lytic and not, and the MAX 232. I'have even been able to get an original Max232CPE. But the board doesn't work still. I get a (...) (22 years ago, 28-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Interactive C Version 4 is available for free download
|
|
Hi everyone, The KISS Institute for Practical Robotics (KIPR), a non-profit educational organization, has been sponsoring continuing work on free versions of Interactive C. In the last week, Randy Sargent has announced Interactive C Version 4, which (...) (22 years ago, 28-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Garmin GPS25-LVS
|
|
Greetings, From the specs ((URL) the unit you have (LVS) supports a RS232C level connection. Since the HandyBoard uses TTL level signals, you would need an RS232C to TTL interface. This interface would be similar to the one used on the serial (...) (22 years ago, 27-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Broken charger board...still broken
|
|
Be sure you get the proper Max232 chip. I bought another, because I was having serial port problems, and thought it might be the Max232 chip... But the new one I bought wasnt *quite* right. What happened was in IC I could download pcode if I tried (...) (22 years ago, 27-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Broken charger board...still broken
|
|
Hi all, just in case anyone feels like helping, I thought I'd post an update on the current (and very sick) state of the charger/interface board I accidently turbocharged by plugging the 120V adapter into a 240V outlet. As stated in a previous (...) (22 years ago, 27-Jan-02, to lugnet.robotics.handyboard)
|
