 | | Is Expansion Board Servo Voltage Suppose to Be 9v
|
|
Hello again, I was surprised to find that my expansion board servo ports were putting 9 volts. Is this the way the board was designed or is this in error. Most servos I have come across work in the upper 4 to 6 volt range. The servo I have runs (...) (23 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | Help Needed With Serial Output Drivers Syntax
|
|
Does anyone have an example of how to use the 7i9600 serial driver with the Scott Edwards SSC II. I cannot seem to find any documentation. Thanks, Andy Loy andyl@citlink.net (23 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Problem in Battery Power
|
|
Hi Chee, I have been told the power still needs to be supplied from that connector. My idea was to only use two of the four connecting pins (one for plus and one for minus) downward from the expansion board and solder two female connectors (one for (...) (23 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | Problem in Battery Power
|
|
Hi ! I am a research student in Robotic. I am using Handy Board together with Expansion Board to interface with DC motors and other sensory devices. Unfortunately, internal power supply is not adequate for powering my motors. So, I am thinking to (...) (23 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Shaft Encoder for Handy Board.
|
|
Hi Ridzuan, A couple of weeks ago I posted a question here if anyone had experience in using magnetic field sensors for building shaft encoders. The reactions I got lead me to build two shaftencoders using the KMZ10B by Philips. It is all pretty (...) (23 years ago, 5-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | Shaft Encoder for Handy Board.
|
|
Hi there! We have three handy board controllers in our lab. We use it as our mobile robot's controller. Now, we want to add feedback motor control routine and required us to use shaft encoder. I just want to know, the model of the shaft encoder that (...) (23 years ago, 4-Aug-01, to lugnet.robotics.handyboard)
|
| |
| | HB for sale
|
|
MOVING, gotta go... FOR SALE: Handy Board, Serial interface w/ battery charger; computer connector; misc elements from senosor/motor kit (including all 4 motors, most sensors); Interactive C license key ALL for $200 or best offer Excellent condition (...) (23 years ago, 28-Jul-01, to lugnet.robotics.handyboard)
|
| |
| | IRQ and XIRQ pins on handyboard
|
|
Hello everybody, Is it a reason why the IRQ pin of the 68HC11 is not available. On the schema, seems that this pin is always up. If I look in the pcode.asm, the interrupt vector for IRQ ($BFF2) is set to RTI (BadInt) So, if I need to link a device (...) (23 years ago, 27-Jul-01, to lugnet.robotics.handyboard)
|
| |
| | LMD18200
|
|
Hi, I have a question about the PCB that Matt Harlan have made for an LMD18200 H-Bridge. In that PCB seems that the Thermal Flag Output of the chip goes directly out and ready to connet to the HB, but this output will not be, in the case of set, of (...) (23 years ago, 27-Jul-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Any success running IC with W2000 on notebook?
|
|
Hi Steve, I have been running IC version 3.2 without any problems on W2k. Not on a notebook though. You can obtain a personal version of IC 3.2 from NetwtonLabs (www.newtonlabs.com/ic) for $35. Good luck, Willem van Asperen "Steve Mosiman" (...) (23 years ago, 25-Jul-01, to lugnet.robotics.handyboard)
|
