 | | Re: Non-polaroid Sonar
|
|
Hi all, I'm now building the ultrasonic sensor from kam leang's page, did anyone interface it with handyboard?? Can anyone give me some advice on driving it? thanks Frankie Lai 97139371d@polyu.edu.hk (...) to bit_set and bit_clear is not actually (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Non-polaroid Sonar
|
|
(...) No, that's a very good question. It had me confused, too. The second argument to bit_set and bit_clear is not actually the index of a bit at all; it's a bit mask. For example, when you do bit_set( 0x1021, 3 ), the 3 becomes 0000 0011 in (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Polaroid setup w/ exp board...
|
|
John Wynne wrote: <snip> (...) Making the connection to the transducer by hand will very likely damage the electronics on the sonar module board. It says in the Polaroid instructions never to operate the sonar with the transducer disconnected. You (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharge Battery
|
|
(...) Actually, if you had stored them fully discharged then they would likely be as good as they day you bought them. That is the best way to store NiCds. However, if they are kept at a C/100 trickle charge to prevent open-circuit discharge, they (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector 2X driver
|
|
Yes, I run my Vector 2X is slave mode using only IC. I don't worry about missing the last bit since the precision of the heading is only +- 2 deg. It's very simple to code up. -Scott (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Non-polaroid Sonar
|
|
Thanks for your help :-D Just so I'm clear, ref pink book page 10-17. Does the "bit_set( 0x1021, 1 );" refer to bit 0 -EDG3B, and bit_clear( 0x1021, 2 ); " refer to bit 1 -EDG3A. This is what was throwing me, I always thought bits started at zero (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: windows nt and handyboard
|
|
I am also using the icwin from newton labs and that works fine also. Although I have not tried it under win2k, which I must do soon. --peter (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharge Battery
|
|
Im going to jump in here on this one and give an opinion. C/10 for a NiCd is a little much for a trickle charge. C/10 on NiCd's is usually considered more of a trimming type of charge following a higher charge rate of C or C/2 to put the bulk of the (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: windows nt and handyboard
|
|
(...) Actually I am working with Linux, but I gave it a try and it worked just fine. I tested with MS Windows NT Workstation 4.0 Service Pack 5. Just open a command prompt and use this ic-version. (URL) There is no admin-account needed. Perhaps you (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Polaroid setup w/ exp board...
|
|
Hello, I am trying to setup the 6500 polaroid sonar package, but am having a little difficulty. I've soldered a .1uF cap (electrolytic) into the C7 space on the ranging board, connected a 22g wire from J12 to input 7, etc., etc. My problem is in (...) (25 years ago, 16-Mar-00, to lugnet.robotics.handyboard)
|
