| | Re: Please help me unsubscribe!
|
|
(...) Gary, you must have had a GOOD day. Enjoyed the humour. Mike (25 years ago, 9-Sep-99, to lugnet.robotics.handyboard)
|
|
| | RE: VOLTAGE AND CURRENT
|
|
Greetings, My buddies and I encountered a similar problem with the motor drivers. The actual specs on a single "Stock" motor driver is .5A . We needed a a driver to handle at least 1A, so we got the TI motor drivers. We found that stacking 2 TI (...) (25 years ago, 9-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: VOLTAGE AND CURRENT
|
|
the car will almost undoubtedly fry the motor driver on the HB, and having it on the same power will probably generate enough noise to occasionally reset the HB. best bet would be to have the car use its own power and h-bridges, with the control (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: VOLTAGE AND CURRENT
|
|
First of all - get rid of the CAPS LOCK!!! Second of all, if your RC Car draws a Max Current of 3.5 Amps then you'll blow the motor drivers on the handyboard since they're only spec'd to provide 1 A. If the RC car starts asking for more current then (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: Error at address 0x0000
|
|
This was the case for the error that I was getting. I switched to a slower machine and things worked after that. -Jake ---...--- Forwarded by Jacob Levirne/Trilogy on 09/08/1999 03:57 PM ---...--- "Dvorak Viktor" <dvorakv@cesnet.cz> on 08/28/1999 (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Error at address 0x0000
|
|
Hi, I saw that some else also had this error when trying to download to the board in section 6 of the manual. I am also getting this error. I have tried replacing the memory chip, the address hold chip, and the NAND gates. None of this has helped. I (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | VOLTAGE AND CURRENT
|
|
SIMPLE QUESTION TO ANYBODY: I'M PLANNING ON INTERFACING THE HANDY BOARD WITH AN R/C CAR. NOW THE MOTORS OF THE R/C CAR DRAW 1 AMP CONTINUOUSLY, AND A PEAK CURRENT OF 3.5 AMPS. THE R/C CAR USES A 9.6 VOLT BATTERY. NOW , ACCORDING TO HANDYBOARD (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Robot sold
|
|
Hello, The completed and running robot that I had listed here previously has been sold. Thank you all for your interest! Bob Kelly (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | DIY expansion board
|
|
Hi all, I want to add some extra analogue ports and some digital ports to my handy board. I have looked at the circuit schematics for the expansion board and worked out what I need to do. I don't want to buy an expansion board as I don't need the (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: bad GP2D02 link
|
|
(URL) Message----- From: Stephan Adelsberger <astephan@dec1.wi-in...-essen.de> To: Handyboard list <handyboard@media.mit.edu> Date: Tuesday, September 07, 1999 4:06 PM Subject: bad GP2D02 link (...) (25 years ago, 8-Sep-99, to lugnet.robotics.handyboard)
|
|
| | RE: A good toy to hack for the HB?--TIA
|
|
(URL) is from Damark, $60 for the same tank. (If the URL doesn't work go to www.damark.com and search for 'tank') --Chuck McManis (...) (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Handy Board help page
|
|
Check out this link... (URL) (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
|
| | RE: Parts List
|
|
I believe The Robot Store sells the kit for $170...but not including the Expansion board. Check the HB site for the site. (...) (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
|
| | bad GP2D02 link
|
|
What's wrong with Barry Brouillette GP2D02 Home page?? The link: (URL) the main Handybord Page won't work. I get an error message: employees is invalid. Has anyone the correct link or saved the pages&icb local? thank you (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
|
| | exp.bord analog routed trough 5&6?
|
|
Unfortunately I ruined my analog ports 0-3. Is it posible to route the expansionboard analog ports through port 5&6 of the handyboard instead of 0&1?? What do I have to do?? thank you Stephan (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
|
| | A good toy to hack for the HB?--TIA
|
|
Hello all, The school year's starting and I need to commence my annual science project. I wanted a good RC car to hack. The LEGOs aren't sufficient. I don't need speed at all, actually I'd rather it be slow but I can always gear it down. But I would (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
|
| | RE: Use of GP2DO2
|
|
The problem could be in the power circuitry. Are the motors powered from a separate supply ? You could try placing some capacitors between the sensor's power connectors. Ronald -----Original Message----- From: Javaid Iqbal (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Use of GP2DO2
|
|
Hi all, I am using two GP2DO2 on Rug Warrior. Sensors are giving me very stable reading when motors are not running, but when motors are running the readings start jumping around. I am running the motors but the robot is static as I have placed it (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Thank you
|
|
Turns out I just needed a common ground between servos and HB Thanx all! :) Alex (25 years ago, 5-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: servo problem increased
|
|
Alex, My servos shutters when I first hooked them up but it was because the values were out of range. My servos work well in a range of 700 to 3800. Bye, Terry-----Original Message----- From: Alex Stewart <robotman5@hotmail.com> To: (...) (25 years ago, 5-Sep-99, to lugnet.robotics.handyboard)
|