 | | Time Disply
|
|
Is there any way to format the time displayed on the Handy Board screen? I want to display time out to 4 decimal places and no more. Bill Landahl (25 years ago, 21-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: MIT - micromouse rules
|
|
I'll rephrase.... Can anyone give me the link to the BEAM Robot Olympics and micromouse cometition rules and guidelines? Thanks (...) (25 years ago, 20-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Yet another board
|
|
Chuck, I would probably buy it, even for $300. That is if it had all the capabilities you specify and was able to handle all the various sensors and hardware PWM that I currently am working with on the handyboard. Scott (...) Scott Sherman IT Spec. (...) (25 years ago, 20-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | MIT - micromouse rules
|
|
Can anyone tell me the link of the MIT - micromouse contest rules. I have them on hard copy but I was wondering if they were on the net somewhere? Sean (25 years ago, 18-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Memory error
|
|
I just assembled my handyboard, but i get some memory errors (almost everywhere, but the addresses vary in some bytes)... i tested two different RAM chips and i still get the errors. They're intermitent (i get many .........'s then many errors, then (...) (25 years ago, 18-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | IC Code Site Address
|
|
(...) That was stupid! Glad I checked my email before I left. (URL) will be at /IC/code Sorry all. It was past my bedtime (10pm, not a word) (25 years ago, 17-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: IC Code Site is Up
|
|
(...) What's the URL? (25 years ago, 17-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | IC Code Site is Up
|
|
OK, I've done it. I've made a site for code and tips. I'll take anykind of code for any board. The site's up, but barren. I'm leaving town tomarrow, and don't have enough time to get any code listed. I wanted to get it up so everybody can look at (...) (25 years ago, 17-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo?
|
|
Use the servo code on the handy board website. Then connect the yellow wire to digital input 9, the red one to logic power (+5V) ,and the black to motor ground. (...) -=-=-=-=-=-=-=-=-=-=...-=-=-=-=-= Music is well said to be the speech of angels; (...) (25 years ago, 17-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Servo?
|
|
Hello guys. I'm new to this stuff so please help me out with this. I want to wire up two servo motors to the handy board. There are three wires to the servo motors. A red wire for 4.8 - 6 vdc, a black wire for ground, and a yellow wire for a (...) (25 years ago, 17-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Yet another board
|
|
(...) what page was that greg??. url pointers please. thanks aaron. (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Subsumption Architecture
|
|
Hi Lisa, Thank you for posting the link to the ic subsumption code at (URL) downloaded the code to my handyboard and it will help me toward understanding ic . ---...--- (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Yet another board
|
|
Hello Everyone, I've had something of a vision, and I don't think it was spoiled food :-) And I'd like some feedback on it. Bear with me, it requires a bit of set up. After working with Handyboards, Miniboards, 6.270 Boards, BOTBoards and other (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Yet another board
|
|
Chuck, you may find this page of interest. UC Berkeley has put a 68HC11 with a Xilinx chip together for their natcar enter.A RC car race sponsored by national semiconductor. good luck!! Greg (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Subsumption Architecture
|
|
Thanks to all (especially Lisa Meeden) for your responses to my request for behavior control help. I'm on my way to learning! Thanks, - Nick - (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | [Fwd: 19200 serial link / IC site]
|
|
(...) Glad you brought that up. I would, of course, take code for the miniboard, fingerboard, etc. I use the F1 board myself. There are enough people out there who like to port things, anyway. I'll start working on it, but it'll take some time. I've (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: 19200 serial link / IC site
|
|
(...) Whoa! Somebody slap me if I'm wrong, but I thought the HB was incapable of using speeds far above 9600. If it's not, then I've been wasting time. The only thing I could think of doing is building a data buffer, but it seems like that would (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Stepper Motor problems
|
|
I can offer that in my C++ course I learned that in order to pass a variable name into the array size declaration, it must be a const int type. Don't know if that's true for Ic, but if it is, you'll be able to keep your cycle_length variable. (...) (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | HB Serial line speed change
|
|
Hi! Is it possible to change the speed of the serial line to 19200? I need to communicate with a device which has a fix 19200 setting! Martin Martin Frischherz frisch@kapsch.net (25 years ago, 16-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
i was wondering if i can use a dallas DS1225ab-150 for my battery backed ram... i found one on my scrap board. thanks (25 years ago, 15-Jul-99, to lugnet.robotics.handyboard)
|
