 | | Re: Expansion Board Files
|
|
I had similar problems with lib_hb.c. Downloaded it tonight (1800 local time in California, 1 Feb 99). After removing all the "little squares" there were still about 8 or 10 errors. At each error I deleted all white space in the error's location, (...) (26 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: First steps ok
|
|
Hi! Amazing when I listened MY HandyBoard playing the Pink Panther theme!!! Again thank you very much to Fred and everybody who helped him, you really did a very great job! I was waiting for this moment for about three months! (...) I'm very glad (...) (26 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Will the SN754410 support...
|
|
if the worst-case current is 1.5A, you're probably OK -- the SN754410's have thermal protection for over-current conditions. they're rated for an amp continuous, so you're not too far out of bounds. one cause for concern is if the 1.5A measure is (...) (26 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Native 68HC11 C Compiler Followup
|
|
For those who asked me for more information about the Introl Compiler and my code, I have created a web page which can be found at (URL) little background: I had originally planned to release this code back in August. However, at that time, Introl (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Will the SN754410 support...
|
|
I am trying to determine whether the SN754410 motor drivers will support two small DC motors. (without killing the IC's or motor) Or will I need to add a power amplification circuit. The motors are rated @ 6v ?A. Test show that they pull 0.35A (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard and iMac
|
|
way back randy did have it running on NeXT, before NeXTSTEP. the unix sources are pretty clean; probably the only tricky part would be the serial line access. fred In your message you said: (...) B/Serial adapter? (...) s, so I was unable to find or (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Handyboard and iMac
|
|
Hi all, Do you remember me asking if the HandyBoard was working on an iMac with an USB/Serial adapter? Well, all the USB/Serial adapters have been back ordered for the last 4 months, so I was unable to find or try any of them ;^(. But I bought an (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: infrared transceivers
|
|
Would anyone happen to know where I can order infrared transceivers, catalogues, or stores in nyc? (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HB failure
|
|
the buzzing indicates that the LCD isn't connected right (or is dead, as you are guessing). first, please be sure that all 14 pins of the LCD are inserted properly into the LCD connector. then (if still probs), try downloading Kent Farnsworth's (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: First steps ok
|
|
You are right, i was just thinking to do so. I didn't know there were so few resellers, and all so far. Thanks. Stefano. ---...--- (...) (26 years ago, 1-Feb-99, to lugnet.robotics.handyboard)
|
