 | | Re: RC Servo motor internal electronics
|
|
Ideally, I could use an H-bridge on the same board as the "new" electronics and provide expanded feedback such as current sensing or encoder in addition to the normal servo interface. It would also be nice to allow PWM to control the power presented (...) (26 years ago, 19-May-98, to lugnet.robotics.handyboard)
|
| |
| | Handyboard questions
|
|
Has anyone used the eltec 442-3 pyrometer with the Handyboard?? I am in the process of using legos to build a robot, and have a completed 442-3 pyrometer with the lens and all that I got in. I am looking for the best way to wire this sensor, and I (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Harddisk-Crash - HELP
|
|
(...) The Handy Board web site has a mail list archive page, from which you can download archives of past postings. The last item on the list is entitled "Jan 1997 -- present" (which means it's probably huge). Good luck. --Will , , __@_/ \_@__ |/ | (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Pad/Hole Widths
|
|
Thanks, I was going to use a pad/hole size of .050/.028. The default size of my library uses .050/.025. I checked some pin size data and it shows .015 (min) to .023 (max). Allowing .008 to .010 extra and .003 for plating, it seems that the best size (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | Harddisk-Crash - HELP
|
|
Hi all, during a harddiskcrash on my computer, i lost all my handyboard mailings. I the past i had contact with view german people but i haven´t any mail-adresses. Please contact me again !!!!! Bye Bernd Klein ;-) P.S. Is there a way to get all (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Pad/Hole Widths
|
|
Hi Mike check with your board manufacturer for production specification. The via hole size I resently used was 12mil with a via size of 16mil. For Pad/Hole Width use the specifications of the parts you want to put on your board. A hole should be (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | RC Servo motor internal electronics
|
|
Has anyone out there ever seen, heard about, or thought about the details of electronic circuit built into a hobby servo motor to do the positioning and maintaining the position based on the signal pulse sent? I am interested in any information or (...) (26 years ago, 18-May-98, to lugnet.robotics.handyboard)
|
| |
| | Pad/Hole Widths
|
|
Does anyone know what typical Pad/Hole Widths are for thru-hole parts? What about via/hole widths? Is there a web site for PCB geometry sizes that someone could point me to? Thanks -- ---...--- ipscone@halcyon.com Shoot-To-Win! Protect the 2nd (...) (26 years ago, 17-May-98, to lugnet.robotics.handyboard)
|
| |
| | Charging HB-PLEASE HELP ASAP!!!
|
|
Hello. I just got HB assembled and tested. I do not have external NiCDs connected, since I am going to be cutting the power lead and connecting an alternative power source. From what I understand there is an internal battery that still needs to be (...) (26 years ago, 15-May-98, to lugnet.robotics.handyboard)
|
| |
| | E Series MCUs
|
|
I am using an 811E2 part in my handyboard with IC. It is supposed to have problems with this chip. I have not disabled the EEPROM but it still seems to work. I have been having a problem finding the A1FN part. I do not want to buy anymore of the (...) (26 years ago, 15-May-98, to lugnet.robotics.handyboard)
|
