 | | HandyBoard anb Logo ???
|
|
Hi It's the first time I join this list, I was wondering if somebody could give me some biography or link about logo and robots. If I'm "off subject" or if you know a list more involved in this subject please let me know. I plan to use a handy board (...) (27 years ago, 17-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | Dual Hall Effect Query
|
|
Has anybody had any experience with the Micro 8SS27 dual hall effect sensor? I cant seem to get even the slightest response out of it! Do i need resistors of something in between the sensor and sensor port? Thanks in advance ___ IAN | |__ _______ (...) (27 years ago, 16-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Yet another ??
|
|
I don't really see the problem Randy as long as you remember to power cycle the board after every ping (pain in the butt) but until you get the TL851 that will have to do! The translation below should help I hope P.S let me know how it works out. (...) (27 years ago, 16-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | Control of MiniSC servo board
|
|
I picked up a MiniSC servo controller to experiment with. It is driven via serial however. I saw in the FAQ that it is possible to use the Handy Boards serial port, but I don't want to have to download a program to the HB, disconnect the phone jack, (...) (27 years ago, 15-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | interrupts and digital outs
|
|
Greetings, First of all, thanks to everyone who helped me with my hardware problems. They seem to be settled now. Now for the fun stuff! :) Anyway, we are trying to implement a polaroid transducer and we need some socket that we can control the (...) (27 years ago, 13-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | Re: trouble with memory
|
|
well, the dim flashing of either yellow charge LEDs should not worry you. all this means is that the Handy Board is drawing some power. if you have the wall adapter plugged into the Interface/Charger board, simply switch it to "Zap" mode. now, onto (...) (27 years ago, 11-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | trouble with memory
|
|
Dear Fred Martin, I'm in deep deeeep trouble! A few weeks ago I first read about your handyboard and was very excited about it, because I was looking for a controller board for my autonomous vacuum cleaner. So I ordered the PCB from Douglas (...) (27 years ago, 11-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | email change
|
|
I know this probably isnt the right place to do this, but could you please change my email address from mdowney@eng.ua.edu to mdowney@dbtech.net Thanks....Sorry for the intrusion. Carry on! :) (27 years ago, 9-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
EAS is now taking orders for the Finger Board, a very small 68hc11 micro controller board with memory and I/O selects compatible to "Handy Board". You can easily design custom interface circuitry for it by using standard prototype boards. It runs (...) (27 years ago, 9-Dec-97, to lugnet.robotics.handyboard)
|
| |
| | Spectra sonar pin outs
|
|
Here is the pin outs that you requested Randy. The board that you are talking about has a 17 pin SIP connector. What I did is remove this connector and solder a ribbon wire to the following pins: Signal Pin # (pin 17 and pin 1 should be labeled) GND (...) (27 years ago, 9-Dec-97, to lugnet.robotics.handyboard)
|
