 | | Procedure to get off mailing list?
|
|
Hi all, I was wondering how do I get off this mailing list? Thanks..... ===...=== Dale Bergman P.Eng Systems Engineer T Telehealth Solutions Computing Devices Canada. 1020 68th Ave N.E. Calgary, Alberta, Canada. T2E 8P2 Voice: (403)295-6778 Fax: (...) (27 years ago, 7-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Shaft Encoders
|
|
Has anyone used an comercial optical encoder to monitor wheel velocity on their robot? Most of the ones i have seen use between 100 and 500 pulses/rev. This is a lot for the little software driven encoder routines to keep up with. I was just (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Shaft Encoders
|
|
On Wed, 5 Nov 1997, David W. Kammer wrote: We are interested in connecting two shaft encoders to the wheels of our (...) You did not give specifications! Degrees/pulse (optical) or degrees/volt (resistor or LVDT), Speed maximum, Shaft size, and etc. (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | UK SUPPLIERS OF PCBS
|
|
Bill, BB> Does anyone know of UK suppliers for Handy Board PCBs and/or BB> component kits. I looked around a bit for a UK supplier too and found.. well, zip, nothing. So eventually I ordered a Handyboard PCB from Douglas Electronics in California. (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | setting config reg with Win95
|
|
We are currently building a dozen Handy Boards here at the Missouri Area Robotics Society (MARS). Everything is going very well for us, except for the members who are using Win95. The problem has been getting the config register set to 0xC0 with (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Australian Suppliers
|
|
Does anyone know if there is anywhere in Australia that sells Handyboards in either kit form or the PCBs? ___...___ David Perrett Product Development Engineer VIAscan Quality Assessment E-mail: dperrett@vqa.gov.au Phone: 3807 8622 Fax: 3807 8633 (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Help in Assembler
|
|
(...) I think this might be what you want to do: varind FCB $00 * 0 <= varind <= FF ORG $c100 * some location of table var1 FCB 1 var2 FCB 7 var3 FCB 4 . . . varN FCB ? . . tabadr FDB #$c100 * address where table is stored start ORG $c000 LDX tabadr (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Help in Assembler
|
|
Hi, Consider a part of a program: var1 FCB 1 var2 FCB 7 var3 FCB 4 . . . varN FCB ? If I want to use a variable (say X) to determine when to use "var1" to "varN", how can I do this (other than a whole bunch of CMP's). (i.e. when X = 3, I want to (...) (27 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Shaft Encoders
|
|
We are interested in connecting two shaft encoders to the wheels of our Handy Board - controlled mobile robot and use the ICW encoder instructions. Does anyone know of a good source of encoders? Is there anyone willing to share your experience with (...) (27 years ago, 5-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Expansion (infinity and beyond !!!)
|
|
Dear All, OK people, Challenge time while Freds away !! I am trying to work out some code (without the aid of a HandyBoard !) My C is a bit limited, so any help would be gratefully received. I would like to add another 74HC374 to the board, with its (...) (27 years ago, 5-Nov-97, to lugnet.robotics.handyboard)
|
