 | | When Will It Be Available?
|
|
Hi! I got to do some test multi servo-motors. I found out the expansion board is not available yet. When will it be available from vendors? I can make a simple test by using #9 digi-input though. best Regards, Mark Kim (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: RC bot base
|
|
Hi, A few students here at Penn State Abington successfully controlled the Zig-Zag using a 6270 board with both a 6volt and 9.6 volt supply using a .5 or 1 ohm series resistor. If I remember correctly the current is in the 2 amp range when loaded. (...) (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: RC bot base
|
|
I have that car too but I haven't tied it to the handyboard yet because it gets stuck goin sideways! Does yours?? Have you tried the motor function or just the fd() function. The motor function should be able to slow down the motors. If not, the (...) (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | serial data link
|
|
Hello All, I am trying to construct a device to replace the wires between the RS-232 converter and the Handy Board. Of the many questions involved in this sort of thing the first one I'm wondering if anybody has experience with is the matter of (...) (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Capture
|
|
(...) Try my IR routines available at (URL) should handle any # of data bits and any kinds of codes. e-mail me personally if you need more help. /Max (27 years ago, 3-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | IR Capture
|
|
Hi handyboarders! I'm currently controlling my camcorder pan (left-right) and tilt (up-down). My camera is a Nikon VN-310. I have a small (very small!) remote control to make it zoom, record, play, stop, etc. Now the thing is I want to use those (...) (27 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Exp Board ETA?
|
|
Dear all, I must apologize for the long delay and stringing everyone along waiting for the Expansion Board. Even now I hesitate to answer for it is not pleasant to have nothing to show presently. Currently, I am working on the "Advanced Sensing" (...) (27 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | RV: What is the better way to comunicate handyboard???
|
|
---...--- (...) the (...) help (...) (27 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: int/float to string routines?%nu
|
|
[Jeff Keyzer] spake unto the ether: (...) Look at my serial I/O routines (Fred has them on the HB ftp/website with the other user-contributed software), specifically the functions in conio.c and serialio.c. I have both float-to-ASCII and (...) (27 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | int/float to string routines?
|
|
Are there any int/float to string conversion routines available for the handy board? I'm sending data over the HB's serial port to my PC, and I need to be able to send data in string format. (I was originally sending data in its actual byte value, (...) (27 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
