To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6461 (+10)
  RE: X10 X-Cam
 
Don't buy the X-10 system expecting to use it for robotics. Those 2.4Ghz transmitters are directional and therefore are not well suited for the robotics application. Go to Best Buy or shopping.com etc. and buy a 900Mhz transmitter/receiver (actually (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  I/R Strobe/Omnidirectional sender/receiver
 
Greetings all, Looking at some of the new posts like the conductor/piano player has got me to thinking about the multiple RCX interacting scenario. The biggest inefficiency to start with is having to direct the entire RCX toward the other one, have (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) They'll probably do what LEGO wants them to do. LEGO appears to be fairly inflexible and uncreative and will probably stick to their normal policy. LEGO's normal policy seems to be to tell the store it has been discontinued and allow the store (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) If all you need to do is generate a pulse of a certain length, why can't you do something like this? Sleep(1); // synchronize with the centisecond timer Fwd(OUT_A, 7); Sleep(1); // 1/100 of a second Off(OUT_A); Sleep(2); // 2/100 of a second (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I can't understand this. Can you correct your grammar so it is clear what you're saying the average servo needs? - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) The answer is pretty simple, actually. In order to control a servo, you need to use pulses whose lengths are on the order of 1-2 ms. The more steps you get in that range, the more servo positions you can use. NQC can't produce pulses as short (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  a correction! to r/c servo
 
Sorry about that! The resulting 0.03 mS pulse width increments would result in 5 degree increments in the position of the servo shaft. How about that? JB -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I think what John was trying to say was that pulse widths between 0.7 ms and 2.0 ms give servo rotations between 0 and 180 degrees. With 45 steps in that range, you can control the servo in 5 degree increments. Seems to me he was approximating (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
okay.. how about this.. avg servo needs.. 60hz pulses.. 1.0ms pulse width = end point 1.5ms pulse width = middle of rotation 2.0ms pulse width = other end point that is the form of the data to the servo. so you need to out put pulses 60 times a (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) That doesn't make sense either. If a single step of 2.0 ms causes 180 degrees of rotation, then how does 45 steps allow you to control it 5 degrees at a time? (...) Are you saying that the servo actually operates in steps of one degree each? (...) (27 years ago, 20-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR