 | | Re: pneumatics & mindstorms?
|
|
(...) Well, ultimately the pneumatic power comes from the motor that drives the compresser. At a given time frame you can only squeeze so much work out of the motor, and pneumatics is no magic. It gives you great power but still not much speed, if (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Broken links (was Re: pneumatics & mindstorms?)
|
|
I can't get these links to work now. Can anyone find the image and post a new link to it? Maybe someone who actually downloaded it as Tim suggested? (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) After the big piston operates once, how long does it take to recharge the pressure? (...) I did not build a compressor using the large pumps before, only the small pumps, so I believe in your findings. Still I wonder why. The larger pump takes (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) (extra removed) (...) Don't forget, at the actuation end, a pneumatic-based motor should be liquid compatible, something the electric motors have a hard time with. Also, you can run the air lines quite far, so long as you are willing to accept (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199907...net.com... (...) You might try a trim pot in place of the 2.2K and set the room temperature to be the correct value. You could later determine the trim pot value (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Toronto lego robot challenge
|
|
Calum and I were talking about this, a copy is also being sent to lugnet.*.*.toronto ---...--- Forwarded message ---...--- Date: Wed, 28 Jul 1999 21:26:00 -0400 From: Calum Thomas Tsang <tsangc@ecf.toronto.edu> Subject: TORONTO: Mindstorms (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi, I was just wondering where i could find the small pumps that are used to make the compressors. I would like to find it as a seperate piece so that i do not have to buy a whole box. I got a lot of pneumatics with the set 8462 Tow Truck (available (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Hi Nicolas, You will find the parts in the Offical Lego web(www.lego.com) site thru the catalog link. select the service button and then the technic button. This will show you a list of available parts thru the Shop at home service. the part (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) You know, I think I'm starting to get nervous about this 1.5 business. Let's say they do happen to ship a 1.0->1.5 software compatability upgrade. The first question that comes to my mind is: Is the upgrade reversible or irreversible? Any why (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
Well, I accually would feel the new RIS 1.5 will be just new firmware and software. Then maybe a different color casing (maybe the iMac deal with transparance) then just a new stamp on the case. Maybe a new feature like Proximity detection or a some (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Battery cases + mindstorms?
|
|
I don't have mindstorms (or that large a collection of Technic stuff, hopefully Christmas! ;) ), but I've been looking around, and finding creations that use both a mindstorms and a battery box. What does the battery box run (other than lights that (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Battery cases + mindstorms?
|
|
(...) Compressors for pneumatic stuff, or (if you're sufficiently mechanically minded to make a good set of switches) you can use the 3 outputs of the RCX purely to switch power around, and have the power supplied from the battery box. Sounds like (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Yes, I guess friction is the answer. 1) The difference in the surface of the pistons between the two kind of pumps is important. I didn't compute the ratio, but imagine can easily be 1:10 or even more. To get that ratio you need to gear down (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) How much did they cost? It's a real pain to get them by any other means... Stuart -- Did you check the web site first?: (URL) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) It has to be reversible from the RCX brick's point of view, since there is no hardware on the RCX to forcibly reprogram its ROM. Perhaps on the PC side it is not reversible, but there is always the uninstall new, reinstall old process, which I (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) [snip] (...) I truly doubt that LEGO in going to create a new OCX. Their strategy was always focused in creating the maximum sowtware with the less work possible. The OCX compatibility between two very different devices like the RCX and (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) sequence (...) only (...) 51.99 FF, that means 7.93 Euros. About 8.40 USD at current exchange rate. The problems is they don't ship abroad. To get them here in Italy I had to send a check in FF and ask them for shipping to a French address (my (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | A RCX 'Beacon'
|
|
Well, I'm not an expert when it comes to small electronics and making them, so I thought I would post this question to this list. After working with the RCX for nearly a year now, I've found a tool/sensor that I would really like to have, but no (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: A RCX 'Beacon'
|
|
(...) Brian, I share your dream. It's a great idea. Surprisingly enough just this morning I wrote an email to Al Thiele asking for the same thing. I'm obsessed by the problem of knowing the robot position. I had some success experimenting odometry, (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi all, I actually live in Monaco, south of France and I'm about to place an order to Lego France for some spare parts. I can post orders quite easily and send to US using UPS or DHL as some of my company offices are in SF, California. if anybody is (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|