 | | Light Sensor Lead Length
|
|
I picked up a second RIS a while back and was sorting the pieces tonight when I noticed that the lead to the new light sensor was longer then my older one. The older one is 4 inches and the new one is 6 inches long. I looked at both of them closer (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
oops. forgot to divide by 2. make that between 600 and 720 RPM. I called pitsco lego dacta and they report 350 RPM... i wonder if i'm doing something else wrong in my analysis... but i can't find it! anyone else? (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
I found only this post in a search of LUGNET Robotics for "RPM" (...) -- Did you check the web site first?: (URL) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
thanks. i found out that my time axis on my graph had numbers about half of what they should have been, so I got around 350 RPM too. yay. -Ben (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: *** NQC ***
|
|
NQC is actually two things: a language to program the RCX and a compiler for that language. (at first I distinguished between the language: NQC, and the compiler: nqcc, but this was even more confusing) RcxCC is a great front-end for NQC. It (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Keep checking the math. I clocked the motor at 330 - 350 rpm. I used the rotation sensor driven directly by the motor. From analysis of the RCX firmware, the rotation sensor should be accurate to 1250 rpm, so I'm pretty confident of it being in the (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Virtual PC and Mindstorms
|
|
Robolab uses the same RCX as Mindstorms - I have one of each and they are identical (short of the number stamped on the side). Dave (...) reply to: dbaum at enteract dot com (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Dave- Where are you getting that 1250 rpm upper limit from? While I haven't counted exactly yet, I'm dropping only 20 counts out of every thousand at ~15,000 rpm. I had assumed this was mainly gear slop, since it only appears to occur while (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Using a Futaba 9ZAP radio with a built in optical tachometer and the two bladed LEGO prop I got 380 rpm for the gearhead motor and 4320 rpm for the older nongeared motor. Of course this was done with a battery box and brand new batteries so I am (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
My memory is a bit fuzzy here since it was a while back, but according to my notes... * sensors are sampled every 3ms * rotation sensor is a quadrature encoder with a 4:1 gearing in front of it (one rotation of the axle yields 16 "ticks"). * sensor (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Oh! Math mistake on my part... 16 instead of 4. Hmm... the ~15K was an off the top of the head estimate, which would go down to ~4K if divided by four again like it should be :) I'll have exact numbers some time today. Like I said, it is (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) You could get close using the differential as an adder. The ratio of speeds above is about 11:1 (its 11.3:1, but lets keep things as integers). That is a prime number, and we know there aren't any lego gear options that give you an 11:1, so (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Assuming those numbers are correct (I've been too slack to actually look up the tooth counts), I'll give further clarification on my earlier post. I'm using a combination of three 40:8 combos, giving me an effective ratio of 125:1. The gearing (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | 8414 Mountain Rambler at K B Toy
|
|
I wasn't really sure which list to post this to, so I apologize in advance if you don't care about this... I just wanted to let the robotics crowd know about the availability of a pretty good technics set for relatively cheap dough. The 8414 (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 8414 Mountain Rambler at K B Toy
|
|
Chris, thanks for the notice, i am always looking for kits like this to integrate into my Mindstorms projects. Michael Aaron (...) (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 256 Colours
|
|
the problem with that is you have to reboot most of the time, so the solution is to get the freeware from microsoft (i think) called PowerTools 98 or actually 95, included is a piece of software called quickres that allows you to make changes to (...) (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 256 Colours
|
|
I believe the product you are looking for is PowerToys. I don't see a need to change the colors unless performance is greatly affected, so just ignore the message. Sorry if this was already said, I just don't want to read all of the posts. (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | New newsgroup lugnet.robotics.logo
|
|
[Followups set to lugnet.robotics.logo] A new newsgroup lugnet.robotics.logo has just been created. CHARTER/PURPOSE ===...=== -> lugnet.robotics.logo (group): Discussion group for projects and educational activities involving LEGO® and the Logo (...) (27 years ago, 8-Jul-99, to lugnet.announce, lugnet.robotics, lugnet.robotics.logo)
|
| |
 | | Re: hmmm...
|
|
[crossposted to lugnet.robotics & lugnet.robotics.logo; followups set to lugnet.robotics.logo] (...) There are actually many dialects of Logo (which some say is itself a dialect of Lisp). Some of these implementations are heavily (...) (27 years ago, 8-Jul-99, to lugnet.robotics.logo, lugnet.robotics)
|
| |
 | | Re: 256 Colours
|
|
Accually, goto the control panel, then display, then the setting tab. After that, click on the advance button on the mid-bottom (Right side) of the window, When you get into the new window, middle part of it, there should be 3 radio buttons, you (...) (27 years ago, 8-Jul-99, to lugnet.robotics)
|