To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 5321 (-20)
  Wheel Setup for the 8880
 
Has anyone came up with a good way to use the wheel assemblies that come with the 8880 with smaller tires (the 68.8 x 40 Q)? -- Clay Aucoin (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  GORDON'S BRICK PROGRAMMER
 
Just wandering if any one was using GBP? (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Thanks ...Re: Removing red led from light sensor..
 
Thanks for all the advice. I got the parts from radio shack and just made a new light sensor today. Now its time to start working with NQC or GORDON'S BRICK PROGRAMMER or somthing. Patrick Lawrence wrote in message ... (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  adam@hpnc.com
 
I went to helitex today and they has sent out a check yesterday by mail. I should get it monday I think. Also Gary said that it is still not emailing him the orders. Didnt you say you changed the email address to heli212@waymark.net Could you please (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) The slippage is supposed to occur between the micro motor and the pulley, not the pulley and the axle. The micro motor uses a stud (rather than an axle) as its output, and you insert that stud into the rubber lining. Cheers, Hao-yang Wang (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: Sorry for the double posting
 
(...) Franz-Michael, Do you recall what error message Marcus received when he posted? Also, is it possible that he pressed the 'Esc' key or the browser's 'Stop' button while posting the first message, upon realizing that it was missing his site's (...) (27 years ago, 11-Jun-99, to lugnet.robotics, lugnet.admin.general)
 
  Re: micro motor sometimes stuck
 
(...) I recall reading somewhere (but I can't remember where) that the micro- motor has an internal switch to protect it from stall current. If you hold it up to your ear when it's stuck and apply power, you can hear a small click, I think. Haven't (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Sorry for the double posting
 
Hi Todd (or anyone else in charge), I was with Marcus when he wrote the two letters on Mindstorms in China. First he posted one - and got an error message. Later he posted a new one - and got another error message. After that I wanted to re-submit (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Lego Mindstorms in China
 
I have heard that M.I.T. students are comming to China to set up a Lego Robotics League. I would like to talk to some of the students in Beijing so that they can give me ideas for projects for the new Mars Pathfinder. I will make a new robot for you (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  (canceled)
 
 
  Re: micro motor sometimes stuck
 
The micro motor doesn't have an axle output, just a standard stud. David Kadansky wrote in message <3760AC13.5079426F@p...ox.com>... (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
Wow. I never noticed the rubber in those pulleys before. So you insert the axle just far enough to engage only the rubber lining? It seems that if you put the axle all the way through there is no slippage. (...) -- Did you check the web site first?: (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) Well, I thought the reason that we always attach that pulley-with-rubber- lining thing (See (URL) for "friction pulley") to the micro motor is to avoid stalling the motor -- If the torgue is too high the friction pulley will slip. Apparently (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: Robotic Pool Cleaner (Non-Lego Alert!)
 
I got a private reply from Bill Leggett about this device: (...) So it sounds like this thing boils down to some very clever mechanical engineering, but no software or electronics or anything. Still interesting to a robotics fan, but in a different (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
Jeff Blaine <jblaine@shell2.shore.net> wrote in message news:slrn7lvneh.n11....ore.net... (...) A simulation of the LEGO Light sensor circuit I did in PSpice showed that the sensor wouldn't read down to zero just because the way the LED interacts (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) does. Use it only for low-torgue applications, and try not to stall it. -- Did you check the web site first?: (URL) (27 years ago, 8-Jun-99, to lugnet.robotics)
 
  Rolykits
 
Ok, first time on list, but I became interested in the Rolykits, so I searched and I found them. You can order on-line (is there any any better way?) from: (URL) search for Rolykits and they have two sizes: small and large. And while I was there, I (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
(...) What about spinning objects? A spinning object is NOT necesarely forced in circular motion by external force. Try spinning the a wheel, then stop forcing it - it will continue to spin. If you force an object in a point which is not the center (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  (canceled)
 
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
(...) -Unfortunately they're also expensive - US$15 to $40! I got my storage containers at Home Depot. I don't recall the brand, but they're orange plastic with translucent plastic tops, compartmentalized, the compartments are different lengths but (...) (27 years ago, 10-Jun-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR