 | | Re: Removing red led from light sensor..
|
|
Patrick Lawrence <pat@hpnc.com> wrote in message news:FD3pFv.DDF@lugnet.com... (...) Removing the LED makes it work over a wider range (0 to 100), but probably at a slight loss of low light sensitivity. There is an analysis of the subject in the (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Removing red led from light sensor..
|
|
It is actually easier to just place a beam in front of the sensor. The layout of the hole on the beam will block out the LED adn allow you to just use the sensor. DAN In a message dated 6/10/99 6:42:02 AM Eastern Daylight Time, mario.ferrari@edis.it (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Removing red led from light sensor..
|
|
(...) Ralph Hempel describes some non-destructive tricks to get better readings from a light sensor. This is the address: (URL) (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Re: A synchro-drive and a CyberDog
|
|
In lugnet.robotics, Hari Wiguna writes: <snip> (...) Yes, correct. You "drive" it more or less you'd do with a real dog. And when you pull up the leash, it stops. Mario (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Trouble getting VB sample prog working
|
|
Hello, I've been having trouble getting a couple of the various sample VB programs to work (such as the one that can be found on the official Mindstorms site) - every routine call seems to be coughing up this error: "Remember to call Init Comm or (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Removing red led from light sensor..
|
|
I think I read someplace that if you remove the red led from the light sensor it works much better. Has any one done this and if so how did it work? (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Re: A synchro-drive and a CyberDog
|
|
Mario Ferrari wrote in message ... (...) WOW! (...) feel (...) You're welcome. You've taken it to a whole new level. My bot was so primitive compared to yours. And another thing, my PodRacer bot pulls the string. That is the podracer engines (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Robotic Vacuum Cleaner
|
|
I'm working on a wall-following robot to vacuum my baseboards. I just recently hooked up a $8.00 6v mini-vac to the motor output, and I'm mounting a touch sensor near the vacuum brush to detect the wall/baseboard. I had a front touch bumper, but it (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Motor Sensor (fwd)
|
|
(...) I think this topic has long since exited the realm of relevance to this list. It also appears that people are forgetting ettiquette as they are getting pissed off at each other. Please stop this discussion on this list. If some still want to (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Motor Sensor (fwd)
|
|
----- Forwarded message from Peter Hesketh ----- Date: Wed, 9 Jun 1999 20:13:24 +0100 From: Peter Hesketh <pbh@phesk.demon.co.uk> Subject: Re: Motor Sensor (fwd) Sorry, but it is _linear_ acceleration which makes things go in circles. They then go (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
|