To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 5041 (-10)
  Re: recursion (was RE: Would-be hacker queries.)
 
(...) I am not familiar with that function, but I believe I recall a proof in a graduate CS theory class that any recursive algorithm could be transformed into an iterative one. Do you have a reference for this function? For practical purposes, (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Fishing for a tasty linkage/gearing/robotic building thread...
 
Michael Gasperi skrev i meddelandet ... (...) Hey, that's almost our (me and my kids) current project! We have Cybermaster, not RIS, but in this case I think the CM is better, as it have the built-in tachometers for the two permanent motors. We (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: recursion (was RE: Would-be hacker queries.)
 
John A. Tamplin skrev i meddelandet ... (...) Are you sure? I have faint memories from University of a function called 'The Ackermann Function' which was 'recursive in all directions', and couldn't be expressed iteratively. Of course, my memory is (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Robotics Book
 
Hi Nick, We're shooting to release it in time for the Christmas 1999 season. This means I have to finish in August, which means I have to write a chapter every two weeks or so. So far it's going well. I can barely wait myself. Again, this is (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Robotics Book
 
Any idea on when that book is coming out? I can barely wait. -Nick Jonathan Knudsen wrote in message <3.0.5.32.1999051210...et.com>... (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: A recursion question/test...
 
I've been meaning to ask: Do you believe technology exists? It would seem hard to maintain a postition of a Techno-Atheist, given that you're using a computer to post. Just ribbing ya, sorry ;-) (...) -- Did you check the web site first?: (URL) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Right angle turns with parts in the box
 
(...) [snip] (...) make (...) Normally I would use the cat-tracks for this, but it wouldn't be a perfect turn there. For a pivot turn, I would use two of the "monster" wheels geared down as they can really rip if you don't! Put skids on the front (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Fishing for a tasty linkage/gearing/robotic building thread...
 
Hi Michael and everybody, I'm working on a robot (for my book) that uses a single motor to go forward and turn in place. I'm using a directional transmission, based on Michael Powell's original design: (URL) use the outputs of the directional (...) (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Fishing for a tasty linkage/gearing/robotic building thread...
 
(...) I probably need the 3rd motor to power the program reading part of the vehicle. (28 years ago, 12-May-99, to lugnet.robotics)
 
  Re: Fishing for a tasty linkage/gearing/robotic building thread...
 
(...) This is very close to what I was thinking. if you lowered a plate, lifted the bot and then rotated it and then rised the plate lowering the bot. With some clever mechanics you mifgt get the lifting and rotating done with one motor. I would (...) (28 years ago, 12-May-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR