To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4776 (+10)
  Re: LEGO light sensor schematic
 
(...) OK, I fixed that and in the process discovered they should be PNPs. 3Hp83 is a BC857 GP PNP from Philips. Looks better now. (...) I think photo diode used in photovoltaic mode. It looks like it pushes the voltage down from that established by (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...(long)
 
In article <000101be94cb$a8fd58...a@pro150>, Ralph Hempel <rhempel@bmts.com> writes (...) My QBasic program available from www.phesk.demon.co.uk/lego/ can download the Lego firmware from DOS - where can I find your new firmware to test it with, (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
(...) I am not sure how much you can extend the capabilities of the firmware while maintaining its basic dispatch loop. There are some very basic design constraints that would be difficult to change without redoing all of the firmware. If you (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
(...) If you believe you have good ideas for a language, my opinion is that you should propose something to the list, find people who want to work with you on this (assuming you don't want to work alone), ignore the people who say you know nothing (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
I think that a good solution would be to have Legos work as a true operating system that stayed loaded in the brick and would accept downloading compiled programs for it to run. Maybe the firmware replacement idea that has been tossed around could (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
(...) I think new firmware is a good way to go. I would vote for a completely new byte code, perhaps similar in spirit to the original, but designed fresh from the ground up. There is no source for the current firmware, although there is pseudocode (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
(...) If you really want to design a new bytecode that is completely flexible, I suggest using the millions of manhours put into the Java Virtual Machine would be worthwhile. I looked at the idea of porting JVM to the RCX briefly before, but decided (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  RE: Something else is needed, I think...
 
(...) If we are going to the trouble of new bytecode, then we need a new compiler. If we design a new compiler, then what language will it be? Yes, we could use C as the base and compile to pcode which is essentially what NQC does if I'm not (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: LEGO light sensor schematic
 
(...) [snip] I'm happy to see that some of my concerns have been born out with these changes, it looks more like a happy little circuit now. (...) Are we sure that the photodiode is located in the schematic correctly? It doesn't look like its biased (...) (28 years ago, 3-May-99, to lugnet.robotics)
 
  Re: Something else is needed, I think...
 
(...) My thoughts on the JVM: - too complicated for what we need or want - no direct support for interfacing with the RCX I envision the new byte code being specific to the RCX, and as simple as possible to get the job done, which is the exact (...) (28 years ago, 3-May-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR