To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4366 (+10)
  Re: multi-device output controller
 
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) I don't know how NQC drives the ports, but both rcxcc and the RIS software have separate controls for on/off and power level. I just tested setting all 8 power settings - motors operates for all 8. -Wes (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Stepper motor design
 
(...) It realy depends on what form of stepper motor you are using and how the coils are wired up. if you can arange it as two sets of coils you could drive it by hooking one motor output up to one pair of coils and the second motor output up to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
Thanks for checking this out. This is important to know. I assume, then, that the duty cycles are 1/8 through 8/8 as well as off, which would be 0/8. Can anybody verify this (with a scope or something)? I have long wondered whether the duty cycles (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
How about an RCX to RS232 connection to use off the shelf components? Check out this link. (URL) sells a simple serial servo contol that services up to 8 motors via an rs232 port ($49.95). I have seen a simple version adapted for a Palm Pilot for (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  External Power Port Problem..?
 
Esteemed Colleagues, I have two RCXs, both of which have stopped responding to power applied to the external power port. With batteries, they function correctly; with a 9.6v Lithium Ion battery pack attached to the external port, nothing. This has (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  External Power Port Problem..? (fwd)
 
----- Forwarded message from Issac Merkle ----- From: "Issac Merkle" <the_gaff@hotmail.com> Subject: External Power Port Problem..? Date: Fri, 26 Mar 1999 06:08:01 PST I have two RCXs, both of which have stopped responding to power applied to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Why do it? Was: multi-device output controller
 
(...) I have checked this out, and if you use the standard RCX firmware (or other firmware that uses the RCX ROM, then you get the waveforms you are talking about at 125Hz 1/(1ms x 8). You also get polarity information - oh no, I've said too much. (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  RE: External Power Port Problem..?
 
(...) Ummm, It's not clear from your post, and I'm sure you have tried this, but have you tried a different adaptor? I tried to drive the RCX from a supposedly 9V wallwart, and it didn't work. The I used my lab power supply and started cranking it (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Why do it? Was: multi-device output controller
 
Ralph, Thanks for reigning in the rabbit chase! As the originator of this thread I'd like to respond to the 'why'... I keep running out of ports on my creations. I see 5 or 6 as a practical limit. My criteria for a solution: 1. Entirely compliant (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR