To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4366 (-20)
  Re: multi-device output controller
 
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) Are you sure? I wasn't, so I went looking. The NQC docs seem to imply 7 powers levels plus off. Which, technically, is 8 levels of PWM, but if you use all of them, a motor is running at all times. That is fine if you use another motor output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
In my example the RCX output was just used to tell this mythical board which output to drive. Power for the output came from a battery box, always set to on. The RCX can't set direction on the battery box (at least not trivially). alex (...) -- Did (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Stepper motor design
 
----- Forwarded message from Wes Matchett ----- From: Wes Matchett <wes@augustschell.com> Subject: Re: multi-device output controller Date: Fri, 26 Mar 1999 17:34:25 GMT Now that I have brought up that topic, anyone know how to drive a stepper motor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
(...) [snip] (...) Dunno, I haven't looked yet, I just came up with the idea. (...) Because I felt like it? I've seen it written both ways. [snip] (...) Nope. 0 (speed) means off, no matter what direction you are going, therefore: 0= forward, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 12:33:18 -0500 OK now the details. 6. Send to a MAX232 devices and wallah, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Muscle wire and alternatives
 
----- Forwarded message from Joel Shafer ----- Date: Fri, 26 Mar 1999 11:12:57 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller (fwd) Has anyone tried out the Muscle Wire or electronic pistons from this site? (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
There is no need to waste PWM levels on reverse. You can set the RCX motor output to reverse speeds as well, giving you 7 outputs (fwd and rvs) instead of 3 1/2. You need a bridge rectifier anyway; you might as well exploit it to indicate direction. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) There are 8 levels of PWM, so fwd/rev for 4 devices is possible. I originally wanted a separate power input to allow a full 8 levels for each device. This would allow the controller to operate ANY device designed for the RCX ports and not (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Cool. You can also add things like the following: 1. Serial LCD display 2. GPS devices 3. additional infrared send/recieve 4. ANY PC project that is serial port connected! I like the idea of multiple serial channels; this means that you can talk to (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Has anyone tried out the Muscle Wire or electronic pistons from this site? Seems like a good alternative to pneumatics. (...) -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Jim Choate ----- From: Jim Choate <ravage@ssz.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 10:34:22 -0600 (CST) It's actualy pretty easy. Take the analog RCX output, integrate, S&H, A/D, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Hi Bill, ----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 I like the ide that you have but like you, I am not a (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 How about an RCX to RS232 connection to use off the shelf (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) With a seperate battery box (from 8735 for instance) you could power the output full time. In this case you'd probably want to map it to something like this: off - off 1 - output 1 fwd 2 - output 1 rev 3 - output 2 fwd 4 - output 2 rev 5 - (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) And where are you getting motor drive power from? I assume you want the selected motor to run at full power, not at 1/8, 1/4, etc. I'm afraid you're still stuck consuming the extra output for power unless you use a separate power source. (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Dennis Clark ----- From: "Dennis Clark" <dlc@verinet.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 15:27:53 GMT Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
(...) [snip] (...) [snip] Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX can cycle the motors on and off, time it, and send a package a serial message at whatever the fastest BAUD rate is to control a max of N motors with (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Polarity Switch = Pressure Switch
 
(...) Mine required no tuning at all, if that's what you mean. I tried a similar configuration to lu's and found that the throw was difficult to get right. I don't like the overall size of my regulator, but it works like a champ! Cheers, Ralph (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
How well does this work? Contrast with: (URL) on (URL) I got from lu, and which seems to require a fair bit of fiddling to get it to regulate correctly. (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR