 | | Re: Contest
|
|
With the restriction that there are no obstacles in the room, the robot could use the IR-Radar scheme that has been discussed to probe around. If it found an obstacle that was only a couple of inches wide it would know that it was a coke can and not (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
The Dallas robotics group has a similar contest. We can adapt our rules from theirs if needed. (...) Joel Shafer joel@connect.net -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
An interesting proposal. (...) I would presume that adding a third motor (like for a gripper to pick up a Coke can) would constitute a non-RIS only solution, since the RIS only comes with two motors? Although I guess you could capture the can with (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
I like it! LINC (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
Good point - there were only 2 motors. It would be better if it were multiple cans as well. The scoring system on that Dallas contest web page ((URL) looked pretty good to me. It is an interesting problem to drive the bot and pick up the can with (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: flames
|
|
mac wrote: Having had 'my' say I will cease to waste your time ^^^^^ uh... that should be 'waist'. :) ha ha ha. i couldn't resist. and, yes, i know i'm wrong. (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
Let's have a couple of classes of competition. Unlimited class is anything goes. Basic class will be the basic Mindstorm set + one motor. Perhaps we should define a class in between as well. We will have to define the size of the room to prevent a (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
Remember the bit about the new Lego Star wars robot thing - Where you have a setting so that forward drives the motor and backward closes the claw? That's one motor. Set up another like in artoflego.pdf with that flat gear (and the worm gear I (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Contest
|
|
A contest would be an interesting idea, but would it be limited to what you can achieve with a single RIS kit? I have two and the parts are so thoroughly intermixed now, that I couldn't know with any certainty if the elements I used in the (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
It isn't actually that tough to do it with two motors. I can think of two ways off of the top of my head. 1) Motor I - Drives both treads forwards, only drives one backwards Motor II - grabbing the can 2) Motor I - Drives left tread forwards, (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
Two questions: One: Is there any prize for winning this contest other than the adulation of the other participants? :) Two: Does the 'bot have to grab the can? Or can it simply push it to the goal? (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Contest Rules
|
|
I've place a description of the contest and preliminary rules at: (URL) Shafer joel@connect.net -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
(...) Yes! Forget the limitation rules, or at least make the limits on the number of parts a lot higher. To build a bot to meets that challenge is already difficult enough, don't make it even more difficult or very few people will ever make it to (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
(...) No (...) goal? Any method to get the can to the finish area is acceptable. Joel Shafer joel@connect.net -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest Rules
|
|
This contest idea sounds great, but I have one question? Is there a time limit? Wes Benwick -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest Rules
|
|
(...) Any limitations on what is allowed for external lighting? (i.e. overhead lighting) If not, custom paint jobs on the walls and cans will make it trivial for any bot with a light sensor to find the cans. (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
A class for those who only use the basic RIS would suite me well since thats pretty much what I have.. =) -- Kent (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest Rules
|
|
There is no time limit for completion of the course, however, robots with the three fastest times will be awarded bonus points. (...) Joel Shafer joel@connect.net -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest
|
|
Hossepian, Nishan wrote in message <5120EB7B6950D1118DD...SAEMS1>... (...) Gary, has the RIS set contents listed at (URL) you make sure your bot doesn't have more than this on it you are RIS only. LINC (28 years ago, 23-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Contest Rules
|
|
(...) Not really since the can placement will be random. The only "information" on the walls will be about the walls themselves. Color coding the walls white and the cans black is an acceptable solution and I don't think it will be prove to be (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
|