To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 3441 (+20)
  Re: Pneumatic 6 legged walker
 
sorry, its (URL) with work and didn't pay attention to what i was typing. alex (...) -- Did you check the web site first?: (URL) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  SPIRIT.OCX and On For
 
Is there a way using Spirit.OCX to turn the motor ports on the Mindstorm brick for a variable amount of time ? Right now I'm using a timer to turn the motors off, but there has to be a better way. -- Did you check the web site first?: (URL) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Adder/Subtractor revisited
 
(...) I can understand why you'd need a method like this if the two motors were radically different types, but if you're dealing with two identical motors (such as the 9V MindStorms motors), is this really necessary? The tolerances may be a teensy (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Pneumatic 6 legged walker
 
(...) No, I'm sorry, I don't. It was just a quick sunday evening project, and I didn't even make a model which had a compressor built in. But it is rather easy to make one. First, you need to figure out how to make a suitable three phase feedback (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Pneumatic 6 legged walker
 
(...) unixers. Any chance that someone could undo this Intel compression? Regards, Johannes. (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Pneumatic 6 legged walker
 
(...) It doesnt work with MoviePlayer on Mac either.. -- Kent -- Did you check the web site first?: (URL) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Pneumatic 6 legged walker
 
(...) I once played with a Creative VideoBlaster and I've found out that many of the (useful) compression schemes the capture software installed were not available to the general public. I'm sure one of those was used and that's the problem. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Alternative compilers for native RCX code?
 
A brief web search for "H8" and "compiler" showed up a number of people selling, er, H8/300 compilers. One notable entry was HI-TECH Software who have a limited eval compiler freely downloadable - see (URL) I haven't had time to go much further than (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Fw: 360 deg. swiveling electrical connection
 
Are you looking for a Lego pure solution? I have a though about some rotating metal disks that touch each other and are always in contact no matter what the rotation, but am not an EE, so I don't know if polarity would become an issue. trowt (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: What is your current Mindstorm project?
 
(...) [ ... ] (...) This is exactly what I'm working on (as a long term goal). I only got my mindstorm a few days ago so I haven't gotten far. Currently I'm just trying to get my robot to survive in my flat for more than a minute! ;-) The main (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Adder/Subtractor revisited
 
Well, I don't know about your experiences, but I have had tracked vehicles with identical (as much as possible) construction on each side of the vehicle that deviat several degrees for each foot travelled. This was due to the characteristics of the (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: 360 deg. swiveling electrical connection
 
Ben Kimball wrote in message ... (...) What about an axle with wires running along two of the groves (groves made by the cross section of the axle). You could have a two bands of thin metal sheeting wrapped around the axle. To each band you have on (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Fw: 360 deg. swiveling electrical connection
 
I am an engineer with EE training. It would not be a problem if you use two concentric rings. One for the "live" voltage and one for a ground (or positive and negative if you prefer that notation). This is how many real world systems work. Matt R. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: 360 deg. swiveling electrical connection
 
Very ingenious use of Lego. I completely forgot about this method (borrowed from the real world). You will, of course, need to do this on each end of the axle. Can probably use either a thin piece of copper cut into strip to fit inside of bushing. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Alternative compilers for native RCX code?
 
=>From: "Gavin Smyth" <gavin@beeskneesDOTf...OTcoDOTuk> =>... =>A brief web search for "H8" and "compiler" showed up a number of people =>selling, er, H8/300 compilers. One notable entry was HI-TECH Software who =>have a limited eval compiler (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Alternative compilers for native RCX code?
 
It only take up like 5 megs in zip form.. I got em installed.. lemme go check the size of the tree.. 118 Meg total space taken up.. -----Original Message----- From: dave madden <dhm@paradigm.webvision.com> To: gavin@beesknees.freeserve.co.uk (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Alternative compilers for native RCX code?
 
Do you have a URL of where to download the GCC/EGCS compiler? Yes, I'm lazy and don't wish to hunt it down. :) I tried searcing this NG for 'compiler' but did not find a ref. for this one in the messages located. thanks, -Wes dave madden wrote: (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Ultrasonic Radar
 
I'm interested in the message you posted to the LUG news server about interfacing an ultrasonic range finder to the RCX. I have a project in mind that could use this, but I lack the time and skills to develop it myself. If you ever get one working, (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  pneumatic tubing
 
Is there any way to get cheap tubing, other than s@h service packs? Has anyone found any other type of tubing that might work? I'm looking for something I can find at a hardware store or a medical supply store that will work the same. Thanks... John (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Variations on the "ADDER SUBTRACTOR" ("differtrans" ?)
 
(...) -- Technical Support requests should be sent to support@opendisc.com Joe Greene Technical Support OpenDisc Systems, Inc. Boulder, Colorado, 80301-2442 USA 303-546-0460 Joe_Greene@OpenDisc.Com (28 years ago, 4-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR