To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23779 (-10)
  Re: caster wheel design
 
(...) Another "microcaster" is the style used in "ERBIE the Robocar" discussed here (URL) made with a 2x2 turntable, a 2x3 plate, and a single wheel (URL) works surprisingly well, so long as 1) The weight isn't huge and 2) the surface isn't too (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) Move the other wheels or the CG so that the caster doesn't support much weight. No matter what your design, a caster that carries a lot of weight will not work well. The large turntables will have a lot of friction when carrying a lot of load. (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: I2C bus for Lego RCX
 
OK, that's neat! That's a novel way to attach to bricks and electrical connectors. Is the $36 before or after the $10 discount ? Either way, I'll probably be buying one to play with. -JSM (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
If you are planning on running on smooth surfaces, you might be suprised at how well your robot drives and turns with just one of those domed 2x2 'gliders' instead of a wheeled caster. ---...--- Steve Baker ---...--- HomeEmail: (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) How heavy is this? A caster needs an offset, but making this offset as small as possible should reduce bending. I usually use a medium pulley on a #3 axle; either end of the axle is held in the pin hole of a Technic crossblack, while short (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  caster wheel design
 
Hi, I´m tring to build a robot that may use a caster wheel, But i am running some serious problemes in it design. If I use an axle or pin for the caster, it will bend. (the robot is quite heavy). So i tried to use a turntable as a caster axle, but (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: I2C bus for Lego RCX
 
(...) Very nice job as usual... as I told you before, I really love your PCB to RCX electrical connectors! (...) Special mention to your Wink Kit (URL) very cool introduction to LEGO sensors building! Philo ...not affiliated in anyway to Mindsensors (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: Robolab as a tool for teaching programming
 
(...) Note that the LEGO Company appears to agree strongly with you. From a press release I just read: ---...--- NEWS RELEASE – March 28, 2005 – NI today announced The LEGO Company uses the NI LabVIEW graphical development environment and NI (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
 
  Re: GBC 6 - the obsession continues...
 
(...) Well, until the video is uploaded, here are some of my pictures from the event (after moderation): (URL) link showing the whole thing: (URL) And as Iain I'd like to know what's inside the black box! Ahh, but that was truly the beauty of (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
 
  I2C bus for Lego RCX
 
Some thing Extremely new :-) I2C bus interface for RCX. Now we can connect any I2C device to RCX. You can use SRF08 or SRF10 with RCX very easily without tampering your RCX Have look at (URL) lot of new things at www.mindsensors.com Nitin (22 years ago, 29-Mar-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR