To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23244 (-20)
  The Great Ball Contraption
 
In an attempt to provide Technic & Mindstorms builders the same cooperative building opportunity that's available to Moonbase, Castle, and Town/Train builders at Brickfest, we present to you: The Great Ball Contraption. When it's assembled at (...) (22 years ago, 7-Jan-05, to lugnet.robotics, lugnet.technic, lugnet.trains, lugnet.events.brickfest, lugnet.events, lugnet.announce) !! 
 
  Re: RCX Sensor Port
 
(...) Experiments completely second that, see this V/I curve I measured while preparing my (URL) GP2D12 interface>. Philo (URL) (22 years ago, 7-Jan-05, to lugnet.robotics, FTX)
 
  RCX Sensor Port
 
I've been looking into the interface of the RCX sensor port, as well as studying available information. This page from Stef Mientki suggests that the port uses a current source: (URL) believe this to be correct. According to the circuit topology and (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: Uses for tacho wheel?
 
(...) Whilst white tacho wheels were used by the barcode truck for speed sensing (on the truck for variable engine rev sounds), the Star Wars UCS X-Wing used grey ones on the cannons(?) on the wings. Tacho wheels have 8 slots that will hold flex (...) (22 years ago, 6-Jan-05, to lugnet.robotics)
 
  Re: Uses for tacho wheel?
 
(...) They were used to interupt the light beam/sensor on the Code Pilot allowing the Code Pilot to sense shaft rotation. -Rob. (22 years ago, 5-Jan-05, to lugnet.robotics)
 
  RE: Uses for tacho wheel?
 
If you point a light sensor at them, you can use them as a rotation sensor. They are also available in one of the NBA basketball sets. If memory serves, they used it as a gear that was part of a ratchet mechanism to keep the wind-up motor from (...) (22 years ago, 5-Jan-05, to lugnet.robotics)
 
  Uses for tacho wheel?
 
Attempt #2 at this post... I recently aquired (via the "grab bags" at LEGO stores - wonderful idea, second only to PaB for me) two of the "tacho wheels": (URL) played with them only a little, but how do you *use* these things? I'd download the (...) (22 years ago, 5-Jan-05, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
(...) Here's the (hopefully) finished circuit diagram for the IR Transceiver, complete with semiconductor component types and bold lines. I changed the supply rail voltage to concide with the zener diode voltage. There's also a space on the board (...) (22 years ago, 4-Jan-05, to lugnet.robotics, FTX)
 
  out
 
Please put me out of the adress list. I don't want to receave any post any more. Tanks (22 years ago, 3-Jan-05, to lugnet.robotics)
 
  Re: 2-wheelers
 
I've been looking at that little piece of code, and trying to duplicate its effect in my YAL-based program, without much luck. When I had Steve's code running, it did tend to stay in one spot, but it eventually became unstable. At this point I plan (...) (22 years ago, 2-Jan-05, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
hi Mark, i have learned a lot from your RCX IR Transceiver Circuit. Things i did not know before. But please dont forget to show us that Sensor Board Circuit. As far as i know, a real introduction into designing RCX selfmade Sensors is not available (...) (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  New invention instructions
 
Where can I get new inventions and their building instructions besides those given in Lego Mindstorms Robotics Invention System 2.0? (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  Re: 2-wheelers
 
(...) I think another huge difference (for me at least) is that Steve's code learns where the upright position is, while most of the others need to be put down in the correct position. (That is what the piece of code does in the 50ms if()). John (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  2-wheelers
 
I don't know if anyone cares about this, but -- I think I figured out something about Legway-type bots and the software that drives them. The puzzle is: why do some versions need a full PID controller (Proportional-Derivative Integral feedback), (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Transistors used in Lego Electronic products
 
Can anyone tell me what type of transistor is in a surface mount package marked "E16"? They're used in the Cybermaster radio tower. Are the transistors NPN or PNP? Do they have the usual pin-out (collector on its own, base and emitter on the other (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: controlling RC-servos
 
(...) Again, I forgot the link : (URL) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  controlling RC-servos
 
Ultimate ROBOLAB v. 1.4.5.7 now has the feature to control 1 to 3 RC-servo motors with full access to the normal Ultimate RCX-functionality. This version will be available soon for beta-testing. Cheers, Claude (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
(...) Thanks Mark, it's on my page, but as I said it's mess, so it's on a slightly different page: (URL) hope to rearrange my Lego Website in one of the next months, but first I've to write a decent html editor ;-) cheers, Stef (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
I recently implemented a new motor control "source" specifically targeted at PID algorithms in the new firmware. It takes a signed number in the range -128 to +128 and converts it into a motor control command. -128 to -1 is reverse direction and (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
(...) that would be interesting, but I meant the wheels. (22 years ago, 31-Dec-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR