To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1821 (+20)
  Re: sensor connectors
 
OOoopsss... LegoMajik@aol.com not LegoCork, that's Mindstorms name. Dohh!!! (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  RCX Serial
 
I'm embarassed to post with such a trivial discovery, but in the hopes of saving somebody a little time: You can get the serial port to transmit under legOS by doing *((char *)0xffd0) = 0x09; // TCR *((char *)0xffd1) = 0x13; // TCSR *((char (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  R/C Servo to Legos
 
Does anyone have a solution for coupling the output of an R/C servo to something like a Lego axel? Thanks. (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
You could glue a lego gear onto the servo horn and axles into that. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
The srevo parts are Nylon, hard to glue on to that. I dont think gooping on epoxy would hold vary well, might be wrong. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  lego train and motors
 
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  sensor details
 
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Sensor ideas
 
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: Mindstorms CD and Soft Windows
 
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Voltage or resistance
 
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  The Bed Mill
 
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Voltage or resistance
 
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  More input
 
After realizing that the input ports read resistance, I had an idea. Suppose that I used a network of switches and parallel resisters to differentiate between switches? Here's the circuit I have in mind: gnd-----+--[22k]------ switch --+ A | | (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  (no subject)
 
After reading Dave's commentary on the RCX's ADC system, I did a few more test's, and found that I could easily predict the value that the RCX would produce for a given resistor. Just use the voltage divider formula - V=R2 / (10,000 + R2) and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Mindstorms CD and Soft Windows
 
I have tried Virtual PC running Windows 95 on my G3 Mac and it doesn't quite work. The software itself runs (albeit with a bit of stuttering on the audio). The problem is the connection to the IR tower. The software doesn't recognize that the tower (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  BotCode
 
I am impressed with the amount of work done with RCX and alternate systems for coding and control. I suppose this is old news to most of you but BotCode is a very nice package for those that want to ditch the Lego interface. (URL) Clemens, Associate (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Re: Sensor ideas
 
(...) I have thought of a simple level sensor that would use light sensors, a ring pipe, and a ball bearing. Drill holes through the ring, aligned like spokes. Place light sensors on the outside of the ring, facing in. Set the ring like a wheel, and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR