 | | Re: Slightly off topic - How to access game port & joystick from Visual Basic
|
|
(...) I don't know if this is helpful, probably not, but if it was in C++ I would tell you to give a look at the Multimedia extensions "mmsystem.h" and "winmm.lib". Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS problems
|
|
(...) How are your batteries? I've found out that with my CyberMaster and with almost spent batteries, when a motor worked with a bit more load than was supposed, the unit shutdown entirely and it loose all memory in the process. Because it's a RCX (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Mindstorms CD and Soft Windows
|
|
Will a translation utility such as soft windows; Virtual PC allow me to runt he Mindstomrs Windows 95 CD from my G3 Mac? (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | sensor connectors
|
|
I've been reading the pages on making sensors. Does anyone know the details of the sensor connectors. Most of the sensors have two contacts, while the RCX connectors have four. I would think that one of these four must be a power pin and one must be (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Slightly off topic - How to access game port & joystick from Visual Basic
|
|
The Microsoft site does have an excellent example of joystick programming for Visual Basic. Go to the VB start page and examine the downloads. There are about one hundred listed including the joystick example. The MS site does change frequently . If (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS problem
|
|
I have tried this with brand new batteries.. still the same result.. I am using rcxfirm to send the firmware across to the rcx unit. The download seems to run fine, and ends with a beep from the rcx unit, after this beep the rcx unit shuts down and (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | legos problem solved
|
|
I compiled firmdl for winnt using the cygwin tools and now everything is up and running.. I plan on making all of my binaries for winnt available as soon as I get home from my holidays... Thanks for everyone's help Jonathan (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Mindstorms CD and Soft Windows
|
|
SoftWindows will give you access to the serial port (with a little configuration) so it should work. On an SGI machine you can't run the port over 9600. I'm not sure about Macs. I only worked on the SGI versions of SoftWindows (V1.25 to 95 V1.01). (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Non-standard differential wanted
|
|
Just wanted to let everyone know that I updated my webpage with this design. The page is (URL) It now contains pictures of a robot using the address/subtractor that my father built. His layout of the adder/ subtractor is more efficient (direct drive (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor connectors
|
|
2 pins are power and 2 are ground. It's made that way so the connector can go in several ways. You can reverse motor direction just by turning the power connector at either end. LegoCork@aol.com (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor connectors
|
|
OOoopsss... LegoMajik@aol.com not LegoCork, that's Mindstorms name. Dohh!!! (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | RCX Serial
|
|
I'm embarassed to post with such a trivial discovery, but in the hopes of saving somebody a little time: You can get the serial port to transmit under legOS by doing *((char *)0xffd0) = 0x09; // TCR *((char *)0xffd1) = 0x13; // TCSR *((char (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | R/C Servo to Legos
|
|
Does anyone have a solution for coupling the output of an R/C servo to something like a Lego axel? Thanks. (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
You could glue a lego gear onto the servo horn and axles into that. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
The srevo parts are Nylon, hard to glue on to that. I dont think gooping on epoxy would hold vary well, might be wrong. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | lego train and motors
|
|
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | sensor details
|
|
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Sensor ideas
|
|
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|