 | | Re: New ROBOLAB pages....
|
|
The IR tower can be used on a MAC using ROBOLAB and a MAC cable for the tower. Pitsco ((URL) sell the MAC cable (bundled with the tower) (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | ROBOLAB in Europe
|
|
Hi all Is somebody outthere aware of a possibility to buy ROBOLAB in Europe (Switzerland to be more specific). I am proud owner of the Mindstorm Robotic package but would like to buy the ROBOLAB software for my Macs too. Thanks for any hint along (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Batteries?
|
|
(...) How about using rechargeable alkaline batteries? (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | RE: space shuttle technic set cost?
|
|
Yes, 8277 is mostly good for getting lots of long beams in yellow and grey. However, it also contains a good number of "push-pin pegs". These are like the normal black 3-beam friction connector pegs, but with a bushing attached on one end. They come (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Laser pointing devices could cause damage
|
|
(...) Well, I didn't even take that into consideration when I tried it. It worked, and I haven't noticed any change in the performance of my sensor. I'm not exactly sure how the sensor works, but I'm pretty sure it's a CdS photoresistor, so the (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Robot Battery Level
|
|
I'd like to program my robot to beep for attention when the batteries start to wear down, however it appears that only the tower can query the battery voltage. I'd rather not have my computer query the robot and send the battery level back to the (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
(...) I think the Lego tubing is PVC, rather than rubber. Silicone rubber tubing might be more flexible, though I think it will also be heavier. It's most conveniently found in small diameters at model shops, sold as fuel tubing for model aircraft. (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | How do I get off this thing??? 8-)
|
|
How do I get out of this list????? /\/\ark Interactive Media Developer rgbStudio, Inc www.rgbstudio.com (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: How do I get off this thing??? 8-)
|
|
Mark Streed wrote in message (...) Iif you send an blank email to the address indicated you will be unsubscribed from the list. lego-robotics-unsubs...crynwr.com instructions were found in the third paragraph of this page: (URL) write me if you are (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Now one with my address
|
|
(...) ldsmith@pfc.forestry.ca (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Archives?
|
|
Lego Users Group Network (Lugnet) archives the messages on this mail list from the date that it was gateway-ed to the Lugnet news group (lugnet.robotics). They have several Lego related newsgroups archived there. You can find a searchable database (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: How do I get off this thing??? 8-)
|
|
Mark Streed writes: > How do I get out of this list????? Let me guess: you've been hitting the 'd' key for the past month. Bad idea. Now you're going to have to go to the web page to find out. (URL) -russ nelson <rn-sig@crynwr.com> (URL) supports (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Laser pointing devices could cause damage
|
|
It is not a CdS photo resistor. I'm pretty sure its a silicon photo transistor. Anyway you would have to put so much light in it that it melted to damage it. A laser pointer will not hurt it. (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX port information
|
|
(...) The pins are 99% definitely unused. To whoever tries this, good luck with that soldering iron. -Kekoa (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Limited number of MindStorms??
|
|
Is it true that they're only going to make 70,000 sets??? Say it ain't so... (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Limited number of MindStorms??
|
|
The Wall Street Journal says Lego will sell 80,000 by years end and they still can't meet the global demand for these things. Their marketing folks thought they'd only sell 12,000 the first year. Guess they didn't count on the over 30 crowd still (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Limited number of MindStorms??
|
|
(...) It ain't so. That's all they planned to make by the end of this year. (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | All-around-the-robot bump detection
|
|
For those of you with LEGO pneumatics, I've got a question. There seems to be a need for an all-around-the-robot bump detector. Would this work? Wrap soft rubber tubing around the robot, seal one end of the tube, and connect the other to a pneumatic (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) Nice idea, just one problem though... It gives you no idea as to the direction of the collision so the robot would need some other means of locating the cause of the collision and taking remedial action. Still, if you can solve that problem... (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
The tubing is such a small diameter that I think it would take a large surface of contact for enough air to be displaced to move a pneumatic cylinder. Maybe with not-Lego(tm) tubing that was, maybe 1/4 to 1/2 inch [6.35 to 12.7 mm :P ] in radius (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|