Subject:
|
Re: Do I want a micromotor?
|
Newsgroups:
|
lugnet.robotics
|
Date:
|
Wed, 12 Jan 2000 21:39:26 GMT
|
Viewed:
|
555 times
|
| |
![Post a public reply to this message](/news/icon-reply.gif) | |
> The micromotor is much smaller - not much bigger than a 2x2 brick. It's
> geared down a lot, and it's output turns very slowly. I estimate it at about
> 1 turn per second (60 rpm).
...maybe if you connect it to 18 VDC (^;
I think you'll find the rotation is a bit closer to appr. 30 rpm. It's slow,
but it's not terribly slow either. I find it very useful for powering
gripers on end of arm tools for my robot models.
> Some people have reported that it easily jams if not used properly.
It most certainly does. I find that a "slipping" pully on the end of the
shaft works well, preventing the motor from stalling and jamming. If I use a
tight pully on the end the motor almost always jams and stops.
What I'd like to know is how they fit the gearing inside of that tiny, tiny
case... Anyone taken one appart? (^:
Iain
--
tokama http://www.oxford.net/~hendryjr
ICQ UIN 5362826
AIM Linjerflyg
h e n d r y j r AT o x f o r d DOT n e t
|
|
Message has 1 Reply: ![](/news/x.gif) | | Re: Do I want a micromotor?
|
| (...) I took one apart, which was terminally jammed since the day I got it. The gears are extrememly tiny (nylon gears with teeth maybe the thickness of 1-2 human hairs), and are made in such a way that an outer gear surrounds the inner gears (I (...) (24 years ago, 14-Jan-00, to lugnet.robotics)
|
Message is in Reply To:
![](/news/x.gif) | | RE: Do I want a micromotor?
|
| The micromotor is much smaller - not much bigger than a 2x2 brick. It's geared down a lot, and it's output turns very slowly. I estimate it at about 1 turn per second (60 rpm). You could use it for positioning (moving an arm or a lever) where you (...) (24 years ago, 11-Jan-00, to lugnet.robotics)
|
7 Messages in This Thread: ![Do I want a micromotor? -David C. Pyatt (11-Jan-00 to lugnet.robotics)](/news/x.gif) ![](/news/246.gif) ![Re: Do I want a micromotor? -lego-robotics@crynwr.com (Russell Nelson) (11-Jan-00 to lugnet.robotics)](/news/x.gif)
![](/news/x.gif) ![](/news/268.gif) ![RE: Do I want a micromotor? -lego-robotics@crynwr.com (Tilman Sporkert) (11-Jan-00 to lugnet.robotics)](/news/x.gif) ![](/news/46.gif) ![You are here](/news/here.gif) ![](/news/46.gif) ![Re: Do I want a micromotor? -lego-robotics@crynwr.com (One Time CR-X) (14-Jan-00 to lugnet.robotics)](/news/x.gif)
![](/news/x.gif) ![](/news/268.gif) ![Re: Do I want a micromotor? -Carsten Müller (17-Jan-00 to lugnet.robotics)](/news/x.gif)
![](/news/x.gif) ![](/news/68.gif) ![Re: Do I want a micromotor? -Philip Ogston (17-Jan-00 to lugnet.robotics)](/news/x.gif)
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|