To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8621 (+10)
  Re: HB Expansion kit
 
---...--- (...) Yes (...) ----6---J2-19 pin ,J19-two 4 pin,J6-4 pin,-one 14 pin for the LCD,-one 4 pin lower r.h. over digital 0,1,2,3. on the hb. All go on the outer edge of the board except J19. Hope this helps, I was also pleased with the kit (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Mindstorm Mac Patch
 
Has anyone had success using the Mac patches for Mindstorms with an Apple PC compatibility Card? (URL) have a 12" Apple PC Compatibility Card and have tried both patches with no success. I would like to hear from someone who has gotten one to work (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  infrared distance sensor
 
Hi, I've just received a Sharp Digital Infra-Red Ranging System (GP2D02) and I'd like to connect it to the handyboard. The device clocks the data in on a digitial input but requires the clocking pulses to be no longer than 200 microseconds. This (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Re: HB failure
 
(...) Thanks for your response. When we load the pcode_hb.s19file with the right CONFIG it seems to load properly. We then turn the HB off and back on and try to load the Interactive C. This does not work at the computer says "attempting to linkt to (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  NQC Barcode program
 
The following is a program someone made on the mindstorms page. There is an error on line 13 but I can't figure it out. I'm not all that experienced so it may be something simple I don't know. Any way, have a look: //This program will decode a "3 of (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  CodePilot (Was: Re: RCX Train)
 
(...) Hey, speaking of barcodes, has anyone created a robot with both an RCX and a CodePilot? I think I may give that a shot. It'd be helpful if someone had already cracked the "compressed" barcode scheme LEGO uses... any ideas? Cheers, Ben P.S. (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  Re: ** voltage dropping and current limitting**
 
Dear Mike, I believe the 16 V is rms value. If you attach a capacitor across the bridge rectifier under no load condition(output terminals are open), the capacitor gets charged not to 16 V rms but to the maximum value ie Vm=16*2^0.5 which is about (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  NQC - ASM command
 
What functionality does the ASM statement give? Does it allow you to directly specify firmware opcodes or is it lower level than that? There are two things that I would like to do. One is to have direct access to the speaker, and the other is to be (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  Talking robot
 
Has anyone toyed with the idea of having your robot talk? I've thought about trying to convert a wave file from pulse code modulation to frequency modulation and try to get it to play on the RCX but I don't think that there will be enough resolution (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  Re: NQC Barcode program
 
(...) That someone would be me. There's no error -- you just have to use the right language. :) Anyway, this is not Lego RIS code (or whatever they call it), and it's not NQC code. It's Perl. Sadly, the Lego site only allows you to upload one (...) (28 years ago, 31-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR