To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8366 (+20)
  RE: navigation with compass
 
(...) -- Did you check the web site first?: (URL) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: AC Adapter Specs?
 
(...) Look on your RCX. Any normal DC adapter between 9 and 12 Volts. ---...--- ---...--- Sam Edwards "On the keyboard of life, always keep one finger on the escape key." -- Did you check the web site first?: (URL) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Ball gear
 
I got a ball gear with some set the other day, and it seemed like a useful part. On the set it is just a decorative "knob" thing, but i should believe it is useful for something beyond that. I cant get it to mesh properly with ordinary gears. Any (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: AC Adapter Specs?
 
I have looked on the RCX and I've noticed it does say "9-12V ~". From what I've gathered the "~" means polarity doesn't matter. My concern is the mA rating of 9 volt adapters. Radio Shack has about 6 different types each with a unique mA rating. (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: Ball gear
 
If it is the one I am thinking of it does not mesh well with any of the other standard gears. This part is meant to be placed in the middle of a ring with 4 ball joints sticking off the outside edge. It is used to adjust a helicopter cyclic in the (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: Ball gear
 
(...) The "ball gear" part is used to transfer rotation momentum to a tilted axle. In the 8880 Supercar (URL) is used to make steering wheel drive. (Actually, it has 4 wheel drive, steer and suspension.) It is also used to make a tilting helicopter (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: batteries port
 
(...) That sounds like too much voltage for the HB. I think I remember reading that the HB runs on up to 12 V max. Check the Handy Board Technical Reference. There are much better ways to run motors that require higher voltages. Try using a separate (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: navigation with compass
 
(...) Richard (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: Wirz LMD18200
 
I'm not familiar with the Wirz board, however the board I built used the regular "motor output" of the handyboard with no modification required. The trick was to use an opto-isolator to "recover" the forward and backward logic states. That was done (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Sound Sensor Mic
 
If you are having trouble finding the crystal microphone used in my sound sensor I've found the earphone from a crystal radio kit works OK. Radio Shack sells a kit like this for about $7. (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Interactive C-OS8 Downloading Problems
 
I have nearly teared my hair out trying to get my HB to to DL on a my OS8 6500 Mac. I though there might be someting wrong with the HB and replaced 5 chips. Today I took my HB over to a friends house who has a Performa 475 and hand had no problems. (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: DATALOG and C
 
Michael Gasperi wrote: The UploadDatalog and SetDatalog are Immediate Commands and (...) What do you mean by this? Do you mean they can't be included in a program running on the RCX? Or can't be included in a program running on the host PC? (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Analog Ports
 
I have the MTJPRO11 board by Mekatronix as well as the MIT HandyBoard both use the 68HC11A1FN mcu. I am using hacked Sharp GP1U58 'tin can' detectors so that they output analog voltage from 1.5 to 2.5 ( effective proximity range is approximately 4" (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Robolab for the World!
 
(...) No, we sure wouldn't. I mean, all software on all our machines is quite legal, right? I say to you, sir, Poppycock! Jasper (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  RE: DATALOG and C
 
There is no way that the RCX can explicitly start an upload, it has to be requested by the PC. There is no problem however aquiring your goal with messages or variables. The best way I have found to achive your goal is to let the RCX signal to the (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: AC Adapter Specs?
 
(...) No. If you take one with too small a current rating, however, you could overload the Power Supply and fry that. Or, maybe, you'll find that oyur batteries still drain even with the RCX plugged in :) I would think 800 mAmps should be enough, (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Requesting Pneumatics Links!
 
If you know of a webpage that contains useful pneumatics information, please post! I'm trying to collect all of them and put it on my page for easy access. Not only that, but I want to see what people come up with using the good'ol cylinders. I (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Star Wars Mindstorms??
 
I thought I heard about this... (URL) have more info about this kit? (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: Interactive C-OS8 Downloading Problems
 
cappy, did you use my new "6811 Downloader MCL" version? this has been tested on a variety of Macs running system 8.5 and 8.1. please download it from (URL) me know if this works to download from your 6500. have you ever used the serial port on this (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Analog Ports
 
yes, it's the 47K pullup that's causing the IR's to not work. slice through the trace connecting the 47K to the sensor input pin on the underside of the printed circuit board. fred In your message you said: (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR