 | | Re: Squishy Brick
|
|
(...) Is that the page where there is a 1*4 grey technic beam, pierced by a #3 or 4 axle, with a 16-tooth bevel (?) gearon one side, and a washer on the other? I think they put that picture in all Technic sets, to tell you that the axles have to be (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: homebrew Temp sensor
|
|
(...) Hmm.. why no elco? that is, if you make sure you alway plug your sensor on in the same way, you should get a constant +ve and -ve... Mindstorms does use the standar measuring trick of having DC current run thru the resistor, right? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
|
|
(...) How about using a few large plates (of the type found as baseplates in small to medium sets), and a few basic bricks, possibly with the addition of glue to keep it all together? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: expansion ports
|
|
Jasper Janssen wrote in message <36a90add.169456990@...et.com>... (...) Your examples are irrelevant because they probably don't still have active patents on the pieces and may or may not have ever had patents on all of them. What I was talking (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | NQC 1.1 b1
|
|
Due to feature creep, NQCC 1.0 never got out of beta. I've merged nqcc and the various utiltites (rcxfirm, rcxlog, etc) into a single program called nqc, and added some minor improvements to the compiler as well. The command line has changed quite a (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: homebrew Temp sensor
|
|
Jasper Janssen wrote in message <36a914e5.172025205@...et.com>... (...) Right, you could use an electrolytic if you wanted to make sure you always plugged your sensor the right way. Many people who are in this group do not know the subtleties of (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
|
|
(...) But that would do nothing towards making it truly LEGO electric compatible; coming up with a suitable compartment for the motherboard that leaves room for the expansion board, even if it's not actually connected yet; leaving the display and (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Toy motors
|
|
I tried to use the special RC motor drivers for RC race cars with good luck, they simply connect to a servo output of the handy board and they work great and you can get them in a thousand different configurations like fwd/rev and brakes. They work (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | RCX message's
|
|
Hi everybody, I'm new to this newsgroup, and I've found much interesting information on this group. I'm writing a hypercard XFCN to control the Cybermaster and it is working right now, but I have problems with the following messaging commands : 90 (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Flexible axles!!!!
|
|
It is Lego's answer to K'nex. The sets are searchable by there number at Lugnet. try 3552 I think its on the Lego catalog page as well. LINC Chris Stanley wrote in message <36A8FB60.F345807A@usit.net>... (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|