 | | Re: Scrolling through the LCD messages by the knob
|
|
Hi Gustav, ich habe für mein HB ein Menüprogramm geschrieben, mit dem man mehrere Menüpunkte durchscrollen kann (Parametereingabe etc.) Falls Du noch interesse hast, sag Bescheid dann kram ich mal den Sourcecode bei mir wieder aus ! Tschau Bernd (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: RCX program editor review (second version)
|
|
Mark, (...) If you are referring to the review which is also on the Lego-Robotics wiki site at: (URL) I would think it would be acceptable for to add your own comments to that page. Since the review is originally by Denis Cousineau then I think you (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: IC PROBLEM
|
|
yes, you are having lib conflicts. you should get the latest at (URL) latest has _raw_analog in the .icb file and NOT in the lib_hb.c file. re: synchronizing probs, try running IC in a full screen DOS window, or boot your computer in DOS mode. the (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Super Car 8880
|
|
(...) This gearbox is also used in other kits like the technics Space Shuttle (1300+ technic parts). The gearbox lets you use one motor to gain four different outputs. Looking at the picture you see four dark grey gear wheels. These are not fixed to (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | New hydraulics
|
|
In the 99 catalog ther is mention og a new hydraulics system that has very smooth motion according to the sales-pitch. The sets are not availible in Norway yet, so I wondered: Have anyone seen this new hydraulics, and is it any good? Will it be (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Light outputs on RCX
|
|
Has anyone ran lights from the RCX outputs? I need something brighter than an LED, any ideas? Thanks, Bryan Bible --- __o --- __o Tandem Computers --- _ \<,_ --- _ \<,_ Austin Texas --- (*) / (*) --- (*) / (*) bryan.bible@compaq.com -- Did you check (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I took apart a laser pointer. I put the laser module into a mutilated brick. I added a diode, an LM-317, appropriate resistors and a .1uF capacitor to make a 3 volt power supply. The diode makes it so the laser is on for motor forward, off for (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
Paul Haas writes: > On Mon, 18 Jan 1999, Bible, Bryan wrote: > > > Has anyone ran lights from the RCX outputs? I need something brighter than > > an LED, any ideas? > > I took apart a laser pointer. I put the laser module into a mutilated > brick. I (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: digital and analog port on HD
|
|
(...) A digital port can't have the capability of an analog port, since it has only one bit of information with which to work. (A 256-value analog port has eight bits.) You could perhaps hook an analog sensor up to a digital port using some sort of (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: digital and analog port on HD
|
|
(...) Just thought I would add that it *is* possible (if a bit slow) to read an analog signal w/ a digital port by timing the decay of the signal thru a RC circuit...not a particularly precise method, either. < Watching for the Fedex guy bringing my (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Where is "R4" on Handy Board Extension Schematic?
|
|
I have just finished building the extension board, and, while it appears to work all right, I can't seem to find resistor R4 on the schematic. The power transistor near the on/off switch is getting quite hot with the expansion board piggybacked on (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Douglas Electronics Expansion Board.
|
|
I ordered the kit the first day I could. I got it last Friday, and put it together over the weekend. The douglas board comes with NO assembly instrictions! These are some notes that ought to make things easier for others: RP1 & RP2: The both have a (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: new Throwbots
|
|
(...) I doubt that these joints will be of much use - they're way to rigid, and there is not a real good place to attach a motive link. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I made several diffrent color (even flashing!) lights with the mini xmas lights. they are real bright if you set the output to 8 or they work at any level. I took the bulb out of the little plastic holder and soldered wires to the wires on the (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I just bought 2 of the new throwbots, Granite and Electro. I am not very impressed. The best part about them is the colored gears. Only because I am tired of gray. ---...--- @¿@ (URL) ,-, Follow the adventures of Capt. Jack Napalm! One thing (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) As a first step, how about simple 2 *4 s with logic gates in them? one of the connectors below for power, one output below, and two inputs on top :) Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) Whereas I have lost it several times form turning the RCX off.. a real pain. Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | RE: RCX 2.0 -- ideas.
|
|
(...) Actually I'd be happy with just some Lego resistors, a 2X1 plate with the two studs as contacts and a resistor between them :) 100% pure multiplexed touch sensors Oh well. -- Did you check the web site first?: (URL) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: LOGO with Mindstorms
|
|
(...) Are the exotic sensors (rotation temperature, as described in the RCX program thing) available yet? if so in which sets, or is it just at Dacta? Jasper. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | IC PROBLEM
|
|
Dear Mr Fred Martin/Friends, I had written to the handy board mailing list about a rover that we are making at VESIT-Bombay-India.We were encountering some problems in starting IC,it was saying 'Synchronizing with board' and hanging. I had received (...) (28 years ago, 19-Jan-99, to lugnet.robotics.handyboard)
|