 | | Re: legOS Download
|
|
Brian Stormont wrote in message <367F357F.78F8ECEC@p...jo.com>... (...) It's because Netscape defaults to ascii download mode, which won't work. Only binary mode works, and thats the default for MSIE. Sorry, but i don't know how to change that. (...) (28 years ago, 23-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CdS Light Sensor
|
|
The most likely manufacture of the Radio Shack parts is Clairex. They don't have a web page with data on these parts. Mouser has a few parts with data sheets. I'd guess the RS parts are like Mouser's 338-76c348. The RS parts have a much lower light (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CdS Light Sensor
|
|
The most likely manufacture of the Radio Shack parts is Clairex. They don't have a web page with data on these parts. Mouser has a few parts with data sheets. I'd guess the RS parts are like Mouser's 338-76c348. The RS parts have a much lower light (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: IR Tower
|
|
Dave, I would be curious if anyone has played with the laptop IR as well. It seems like this should be fairly easy to do. I have seen someone doing "something" with the palm IR, although not fully functional. The link is around here somewhere. Have (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS Download
|
|
Brian, Try ie4. That seemed to work. (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | IR Tower
|
|
Hi. I have a Puma IR adapter that I think is fairly generic -- it was provided to work with a Sony digital camera, but it receives regular IR remote control transmissions, and *almost* works with my RCX. However, it appears that the LEGO(r) IR tower (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | RE: CdS Light Sensor
|
|
Does somebody know an industrial reference for a CdS photoresistor? There are places where the Radio Shack reference is not valid. Thanks, David (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS Download
|
|
I have had the same problem. Also using netscape. -- jim (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: AC adapter for RCX: Polarity is irrelevant
|
|
=>From: Bob Stern <stern@batnet.com> =>... =>I discovered that it doesn't matter what polarity voltage is supplied =>by an AC adapter connected to the RCX. Yow! That's a scary discovery! (Not the result, of course, but your experiment design: "plug (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | new 6811 Downloader for PowerMac G3's!
|
|
Hi everyone, I've built a new version of a 6811 Downloader application for Mac that works fine with PowerMac G3's. (It also works with older Macs.) You can download it from the Handy Board home page: (URL) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
(...) WOW! Thanks Don for your post. This is one of the reasons I read this board. So many great minds out here. (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: dc motor output control
|
|
How about lifting pint 8 of the L293 chip and running a wire from it to a 7805 regulator (not the one used for logic). You could also run the wire to a separate battery pack. 4 NiCds in series gets you real close to 5V with no regulator. In motor (...) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | AC adapter for RCX: Polarity is irrelevant
|
|
I discovered that it doesn't matter what polarity voltage is supplied by an AC adapter connected to the RCX. Apparently, the power jack connects to a full wave bridge rectifier. In fact, it may work on pure AC. I notice it maintains power for a (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | ------ MindControl Question
|
|
I have taken a great liking to this program, especially the "Remote Control" part, where you custom config your motors and control witht he numpad. I was wondering as to when you plan on releasing the source code? I was hoping to look at the remote (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
Several list members have asked for instructions on making a simple rotation sensor using the standard Mindstorms light sensor coupled to the light / fiber optic gizmo that comes in the "Extreme Creatures" add-on set. Here goes: 1) The problem: (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | legOS Download
|
|
Has anyone downloaded Markus Noga's legOS files successfully? I keep getting corrupt gzip files. Using Netscape I've tried right clicking and picking "save as", but still seem to get corrupt files. The file size looks right, but all the versions of (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: dc motor output control
|
|
On my first robot, I just took a resistor in-line and used that. It got very hot, though, and didn't work evenly (some of them must have started to burn out before the others did....) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: I need a poloroid sonar board pinout.
|
|
Wayne Try this link. (URL) It shows modifications for interfacing the one step board to a microcontroller. I also have an old one step ($1 at a garage sale) but I have not tried the modifications shown for use with the handyboard. I have taken the (...) (28 years ago, 22-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: RCX Creator Software v 1.5
|
|
You got me..:) Your right...i should have said it only requires you to have the OCX installed and registered. Then everything sould work great. Im trying to get the opcodes setup and sending so i can do it natively but thats a bit of work...so maybe (...) (28 years ago, 22-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX port information
|
|
(...) half the cost of a new RIS, let alone a RCX. But thanks for the link, I'll archive it for now... Jasper (28 years ago, 21-Dec-98, to lugnet.robotics)
|