To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6186 (+20)
  Re: Delphi developers
 
John: I haven't heard about Delphi, but some have created other ways to program the RCX. See my Mindstorms page and look under the Alternate Programming Environments section. The page is located at (URL) Nelson nelsonb@vii.com (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: DC Motor movement
 
(...) Each motor may have slightly different characteristics even though they may be the same brand and model. This is what you are probably seeing. The ultimate solution is to use a feedback mechanism, like a shaft encoder, on the motors and use (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: RCX Command Center
 
Found the problem. I normally run code like this from the D: drive. It seems that unless I have the NQC dir on the C: then it can not find "Command.com". Once I moved the NQC to the C: and remapped my icon, then it alled worked. Would it be (...) (28 years ago, 9-Dec-98, to lugnet.robotics)
 
  unsuscribe
 
unsuscribe (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  ...-help@...
 
(28 years ago, 10-Dec-98, to lugnet.robotics)
 
  -help@
 
(28 years ago, 10-Dec-98, to lugnet.robotics)
 
  autostart of program in mindstorm
 
You can use my free RCX Command Center. You can select the program, run it or stop it, and even run individual tasks. (Of course, it also does a lot more.) See my web page for more info: (URL) Overmars (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Communicating with IR tower
 
The standard way for doing this is to use variable 0 on the RCX. Te robot can set it to a specific valu when it needs something. The PC can use the SetEvent command and the VariableChange event handler to check whether the variable changes. (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Delphi developers
 
RCX Command Center was written in Delphi using the spirit.ocx. It work very easy. (Only note that the On command to switch motors on is called On_ because on is a reserved word in Delphi.) But if you want to write programs to download to the RCX, I (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re. RF data link
 
If the data tx/rx modules can't handle TTL levels is there any reason to have the interface board at the PC end ?, why not replace the serial cable going to the PC with the rx/tx modules ?. Surely this should work. John (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  CM: MotorCurrent
 
For the Cybermaster unit, it is possible to monitor the current of the external motor, measured in milliamps. I assume this can be used to detect when the motor is stalled. Do anybody know the typical values of MotorCurrent when the motors is o (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Communicating with IR tower
 
Hi John, I've been doing this for a while with the Cybermaster. You can simple use the SetVar and Poll commands in immediate mode via the OCX to read and set variables in the brick. Add a bit of handshaking and you have a communications mechanism (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  effect of motor speeds
 
I noticed that settting the motor speed does not seem to have much efect on the speed the robot is moving: 0 = slow 1 = faster 2 = slighly faster than 1 3-7 = about equal to 2 Am I doing something wrong? Or is this standard behavior? Mark Overmars (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: CM: MotorCurrent
 
I only made one test with it, and by the looking at the results I couldn't tell if the motor running loaded, but I may be wrong! The result of the function seems to be: .If no motor is attached, the result is zero. .If a motor is attached and not (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: CM: MotorCurrent
 
(...) Yes, this sounds plausible. My comment on stall detections was probably wrong. Fredrik (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Do It Yourself RF module????
 
Bastiaan: I wanted to suggest that you investigate the Ham Radio community. Some search words to help get you started include PACKET and ARRL. The first is one of the digital communications protocalls used in Ham Radio, and the second is an (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: effect of motor speeds
 
(...) I think so, most problematical is the reduction in starting torque, free running always seems to peak at the same RPM. With an Acrobot based robot I have problems with wrinkles in the carpet stopping it when manoevering at low speed, but it (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: effect of motor speeds
 
(...) I think it depends a lot on the weight of the robot and the type of mobility used. For instants, when I use tracks on my CyberMaster, 1 is very very slow and 7 is fast. All the other numbers between have speeds more or less according to this (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Stepper vs DC
 
(...) Actually, steppers do have some advantages. 1) If you do not have encoders on DC gearhead motors (or wheels, etc) they are notoriously hard to position accurately. Steppers can be controlled very accurately. Most servo motors cannot rotate (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  stepper motors from 5 1/4 drives
 
Okay, another newbie question: What do I need to take out of the 5 1/4 drive, other than the motor to get this to work? Also, what about drivers for the same? Anyplace I can get more info on this? I have a bunch of old drives laying around. thanks (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR