To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5681 (+10)
  Re: CyberMaster memory limit?
 
(...) specific code. (...) with even (...) Works on Windows NT, Win 95, and Linux. NQC runs on Macintosh, although the serial port on a Mac cannot talk to a CyberMaster. Porting to just about any POSIX like environment should be trivial. Someone (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Good 9V motor source
 
Hi all....I'm looking for a good source of 9V gear motors that i could use with the handyboard for a mobile robot. Currently, i am just using the little 9v motors that came with the board, which i have plugged into the cheap gearbox from a toy tank, (...) (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Choosing a shaft encoder?
 
(...) I would have to agree. We evaluated incremental encoders from US Digital. We purchased the "low cost" encoders and paid just over $54 US. -d # rsh -l God universe.all find / -name '*windows*' -exec rm -rf {} \; (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Good 9V motor source
 
(...) Try Lego Technic kits. Start with a basic kit like the Giant Model Set (#8277) for $44, and add a couple 9V mini gear motors (#5225) for $17.50 each and a gear assortment for $4.50. Call Lego Shop-At-Home for a catalog (1-800-453-4652). If (...) (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Good 9V motor source
 
(...) The Bulldozer kit has a decent gearbox in it, however there are some problems with it. The motors are 3v, so you really need to use an alternate power supply. Also, the tracks are not very good at all and will not last under any real use. the (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Extra output for clocking
 
I have a stepper motor controlled by a Motorola MC3479 driver, which basically allows me to input a clock and the direction from the handyboard and the driver does the sequencing. So I'm using 2 pins from the HB's motor output for controlling the (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  uncondition jump to label
 
Hi all, Can we use goto command in IC for unconditional jump to label. If yes, how. If no, any alternative any body using for this. Help would be much appreciated. regards Javaid Iqbal (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Left and right axles rotating at same speed
 
In regard to propelling a robot with both the left and right axles turning at the same speed (or, moving in a straight line): Perhaps this was already suggested, but if not, here is another solution that uses only one differential and two motors, (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
toys r us has 8735 for around $38. tim (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Pneumatic Air Tanks
 
Shane Weston wrote in message (...) You will have much better luck with a micro motor on that switch. I can't even imagine what would happen when the switch reached the end of its throw and a geared motor is still going. A micro motor stalls, but it (...) (28 years ago, 30-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR