To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5646 (+20)
  Re: Worm Drive Question
 
(...) Nope, not me. I never cut on purpose, and anything that breaks gets tossed. (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) tend to slide on the axle over time? (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
(...) I've had good results using the Hall-effect magnetic sensors that Patrick Hui sent with my HandyBoard. I glued magnets into three of the six holes in a Lego pulley wheel and glued the sensor into a small Lego brick. I don't know the part (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
Your program generates a .RCX file of 440 bytes. I've created one with 452 that works OK, but had to stop around that number because after more 2 or 3 lines of code the last task simply disappeared (my program had 1 main plus 3 tasks). I guess the (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
Try a little white glue. The glue helps prevent slippage and can be easily removed with warm water. Another option is a low-temperature "hot" glue gun. Many of the "hot" glue gun glues can be removed with vinegar. Use these at your own risk. matt (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) When did TLG start making white glue?? Cool! <grins, ducks and runs...> (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
(...) hy, I used HewlettPackard shaft encoders HEDL5540 (500 steps per revoltion) with HCTL2020 quadrature shaft counters/decoders. With them you get 500*4=2000 steps per revolution, which is quite a lot. For me They seem to be a good (but not (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
In message <4.1.19981128170141....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) This use of software to determine direction is what I was alluding to in an earlier post when the others were trying to get their mobile to travel in (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
In message <4.1.19981128170141....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) Does this work on Windows NT or Win 95? Dennis (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: legOS corruption
 
(...) Yeah, yeah. I'm sure we've all got "I debugged that with no more than an LED and 3 inches of wire" stories, but only a fool would spurn a logic analyser when it was available. Cheers, Ben. (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Optrex lcd displays
 
I am trying to interface an Optrex DMC display to a miniboard. What pins besides the data lines need to be connected and to what? Anyone used these displays yet, I have two a one line x 16 characters and a two line x 16 characters. The pin out (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
(...) There's nothing unknown about the Tachos. If you need help using them, gimme a call. :-) (...) Yeah, I've also started with that bot. It's very well designed! And I've never exchanged any batteries! :-) (...) The best vehicle would be one with (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) You bet it does! My system is a Win98, which is great since I will need to use the SPIRIT.OCX that only works in Windows machines. Laurentino Martins PS: Why you always send every mail twice? (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
i use US Digital encoders, www.usdigital.com. they are a bit costly, but very accurate, and have quite a few numbers of resolutions. good luck justin (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Optrex lcd displays
 
I must apologize for my last request, upon further investigation I found an excellent resource that answers the questions i posed earlier. For anyone who might be interested, the source can be found at : LCD MODULE TECHNICAL REFERENCE (FAQ) Version (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Choosing a shaft encoder?
 
We're using a track drive system and we're going to be using L.E.D. proximity sensors off of the teeth of the track gears. The tank tracks appear to be very stable but it's still too early in the development to know how repeatable the robot (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Has anyone been experimenting with mapping algorithms?
 
Hi everyone, We've been reading up on the many different algorithms for mapping an environment using autonomous robots. Has anyone else been trying to figure out the best approach to map an area and it's obstacles using less than 32k of memory? (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  A lamer question...
 
Hi all! I'm new here at the mailing list and at lego robotics. I didn't know how can a robot determine its exact position. And now I red something interesting about this in a mail: (...) position and direction where the rover is facing (the (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Sorry all
 
Idiot Netscape ran away from me there. (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: Has anyone been experimenting with mapping algorithms?
 
(...) The two basic approaches are (1) a bitmap, and (2) a list of obstacle coordinates. A bitmap is just a grid of 1's and 0's indicating the presence of an obstacle at each grid point. It can be implemented as a 1-D integer array with a simple (...) (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR