To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5451 (+20)
  Re: One tip, and a few questions.
 
In article <01BE14B1.B5C66E80.e...inum.com>, Eric Hodges <eric.hodges@platinum.com> writes (...) In the fifties I built a heat-seeking swivelling "eye" using that method with valve (tube) technology. The IR detector was an old fashioned glass (...) (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  4x4 'bots (was Re: Misc. Lego parts)
 
Wow! I thought I was the only nut working on such a 'bot. 4x4 models are my fetish. Over the last couple of years I've built several with just Technic parts. I've been hacking for two weeks on a non-sprung steering system with drive shafts. Today I (...) (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  Re: motor port problem
 
(...) to make the connector more physically and electrically stable. (...) of course, only 2 connections are needed to make a ckt. (...) you should figure up to several amps of current flow. (...) it should work fine. good luck. fred (...) (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  Using 30VDC to drive motors
 
Hello, I have finished building Matt Harlan's H-Bridge circuit (from the Handyboard FAQ) and I have come across the following instructions: "Make sure the supply ground for the 18200's is connected to the HB ground. You'll get some very strange (...) (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  MAP Bot
 
I have a idea which is based on a project I worked on back in the 70's. It used one of the sonar devices that Poliord used to foucse their camera with. This device is availible without the camera. It sends a signal based on how far the object is. (...) (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  New user - printf question/problem
 
Okay, this may seem silly, but I've got a very basic question. Just received a new handyboard (assembled, ready to go from Gleason). After charging it up, installing the pcode and booting all works fine. The 'Interactive C' text shows on the screen. (...) (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  Re: 4x4 'bots (was Re: Misc. Lego parts)
 
(...) If your working on your own 4x4 designs I wound definitely take a look at the 8880 Super Car instructions you can find them at: (URL) instructions have a lot of really neat and efficient ways to do things. Unfortunately some of the neatest (...) (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  Re: Misc. Lego parts
 
(...) Sorry if this is old information, but I caught the thread in the middle... I've got some inventories at (URL) Most of these have also been submitted to LUGNET (www.lugnet.com). Dave (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  unsubscribe
 
(28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  RE: New user - printf question/problem
 
I'm still not sure what caused the problem, but a new bootstrap/reinstall of the pcode seems to have fixed the problem. I can now successfully use the printf function. Odd though, that that was the only command that wasn't working correctly. Todd (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Using 30VDC to drive motors
 
Dave As far as connecting the grounds, that just means that the HB and the motors must share a common ground. The H-bridges need to reference the direction and PWM signal to ground and if that ground reference is not the same as the HB's the motors (...) (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Arithmatic operation
 
(...) I've asked for help with the floating point bugs in IC before, and nobody seems to care. Unfortunately, I've come to not use IC floating point variables at all, since I can't trust them. It's all very frustrating since none of the IC versions (...) (28 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
 
  Re: 4x4 'bots (was Re: Misc. Lego parts)
 
(...) I just thought of an idea for making a servo for steering... I'm not 100% sure this will work, as I don't have an angle sensor, but here you go: You'll need a fixed width font: | <--- drive axel +-------+ |o o o o| <--- 1x4 technic beam (...) (28 years ago, 22-Nov-98, to lugnet.robotics)
 
  Re: Arithmatic operation
 
if you are not trying to divide numbers of great precision(many significant figures), then you can try multiplying by some order of 10, performing your division, then dividing by that same order of 10. i have used this before, but not for the same (...) (28 years ago, 22-Nov-98, to lugnet.robotics.handyboard)
 
  Re: pictures of gear differential
 
Digging thru my NEW Mindstorm Kit, I found parts to make a differential. Did the earlier kits not have these parts?? John A. Donaldson (...) (28 years ago, 21-Nov-98, to lugnet.robotics)
 
  Pnumatic Vavles for Mindstorm
 
Check out (URL) like a three-way in-line vavle could make a good replacement for the manual LEGO vavle. 5ms response time. Thoughts? I'm willing to but a couple of samples and attempt to build a workable piece. If it works I'd also be willing to buy (...) (28 years ago, 22-Nov-98, to lugnet.robotics)
 
  Shop @ Home
 
Hi I have just a quick question. I called and ordered a catalog from S@H about 3 weeks ago going on 4. This is my first time dealing with them and was wondering how long it usually takes to recieve their catalog. Thanks, Shane Weston (28 years ago, 22-Nov-98, to lugnet.robotics)
 
  Re: Pnumatic Vavles for Mindstorm
 
(...) Well I must admit that this and the shape memory wire idea are the first two things I've heard suggested that might tempt me away from my official-LEGO-only attitude. The standard LEGO pneumatic valves are no fun at all (who'dathunk they'd (...) (28 years ago, 22-Nov-98, to lugnet.robotics)
 
  Re: Pnumatic Vavles for Mindstorm
 
Nancy Evelyn Gold wrote in message <3657B4F8.F2C6E925@sgi.com>... (...) Be careful. Correct me if I am wrong, but the LEGO valve has a neutral position while these three way valves fully pressurize one port or the other. This is only an issue if you (...) (28 years ago, 22-Nov-98, to lugnet.robotics)
 
  Re: MAP Bot
 
This is exactly what I wanted to attempt, I wonder how small those units are now, would it be possible to modify a brick to hold the parts? -Paul- -----Original Message----- From: John Donaldson <jdonaldson@ghg.net> To: lego-robotics@crynwr.com (...) (28 years ago, 22-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR