 | | Re: moving in a straight line with two motors?
|
|
(...) eh> -----Original Message----- (...) eh> I don't think it works that way. Will hooking 2 motors to the same power eh> source provide twice as much power? I think the limiting factor is the eh> current from the power source, not the number of (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) There needs to be a link to this somewhere: Peter Phillips pointed out a long while back (my messages from him are dated Sep 21) that the specs to the chip are here: (...) drivers. I don't know if he told the rest of the list about this, if (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Buy online in UK
|
|
I am looking for a place to buy the Logo Robotics Construction Kit, and I have found great online stores in the US, but I believe UK will be cheaper for me being in europe. Any good, reliable, online stores to recommend? thank you, Simen Svale (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Op een zekere dag, te weten Fri, 13 Nov 1998 17:21:08 GMT, klom lego-robotics@crynwr.com (Alex Wetmore) in het toetsenbord en schreef ons: (...) But you don't have to drive two weels. When you make one wheel for steering (thus making a (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Aha. For those that can't be bothered to look, maximum output is 600 mA. It also tells us what the bits at 0xf000 do: 10: forwards 01: backwards 11: short (i.e. brake) 00: off (i.e. freewheel) Cheers, Ben. (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) The problem with this is that you now have a car-style turning radius (determined by front wheel deflection and traction) instead of a tank-style turning radius (essentially zero). Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
I believe you are thinking of Leo Dorst's adder/subtractor. I had been eyeing this myself for use with mindstorms, since it would seem to solve the "differing motor RPM phenomena" problem. (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Homebrew sensors?
|
|
I've been brainstorming for a while about what could be done with a kludge. I'm more into the whoosh-bang side of engineering than the beep-zap, so I don't know if it would work... A few years ago, Estes (the model rocket people) made a "rocket (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) kp> There needs to be a link to this somewhere: kp> Peter Phillips pointed out a long while back (my messages from him are kp> dated Sep 21) that the specs to the chip are here: (...) kp> drivers. OK, 500mA per driver. Which, if the rest of my (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) This all depends. The table you gave (presumably from the date sheet), said: (...) Now, Lego uses Off to mean Brake and Float to Off ... (...) Well, you can set the motor to "float" and you do coast. (...) Please explain why there is (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: how to adapt a voltage signal?
|
|
You could use resistors to make a 1/10 voltage divider. If you need high input impeadance, you could build an Op-Amp circuit to divide the voltage by 10. Most ADC chips have a pin that is the reference voltage for the high end of the scale--set this (...) (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Hm. So I just reviewed the data sheet again, and it seems that there is indeed a significant current when the motor is shorted. That sucks. -Kekoa (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
Daniel Miller wrote in message ... (...) Daniel, I could not help but notice that you are into rockets. If so, then whoosh-bang is not the way to go. I think bang-whoosh makes a much better rocket since it should have a loud ignition, then a (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | FT639 and Lynxmotion IRPD
|
|
Has anybody try to interface a FT639 to a Handy Board ? Has anybody try to interface a Lynxmotion IRPD kit to a Handy Board ? (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Homebrew sensors?
|
|
There is a single channel sound sensor on my web page: (URL) was really designed for picking up loud noises like claps. What you want would require two mics and a circuit that would take the difference between the sound levels. Better yet it should (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | The IR beacon, was Re: Homebrew sensors?
|
|
(...) The light sensor is directional without a tunnel. I use the IR tower as a beacon. I've got a perl script that listens for RCX messages. Here's the normal sequence of events: 1. RCX sends the message 2 "Turn on your beacon, so I can find you" (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: coasting moters in nqcc
|
|
Hello all, In reading about moving in a straight line tread there was an issue related to the motor being off, on, or float. If off sets into brake mode and float does really turn them off. I thought that using float for time that the motors are (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) I was thinking of something that sensed amplitude, not frequency. (Like the light sensor, which sees brightness, not color.) Of course, whatever you want for yourself is best. :) I know the logic of taking two sensors and differentiating to (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) Unfortunately the bang comes with the whoosh, often leading to a rapid unplanned dissasembly. Witness the recent destruction of Delta III #1, caused by a 4hz roll oscillation, or the Titan IV that ended in a BFRC due to a clog in its wacky (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Homebrew sensors?
|
|
Why would you need an array to do that? You could do it with three variables: var1 = starting angle var2 = highest amplitude encountered so far var3 = angle of highest amplitude The algorithm goes something like this (in pseudo-C): var1 = (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|