 | | HB woes
|
|
I'd appreciate mucho any help and ideas you all have I am building my HB, finally got the caps and crystal osc. working, and ran the HBDL program to download. All good and fine. I go off and solder in the transparent latch, and while doing so I (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Controling LEGO trains via Decta Control Lab
|
|
Hi All, I have been working on controlling LEGO trains thru the Decta Control Lab and I got a tip to pulse the power to the rails to better control the trains speed. There are 8 power settings via the ctrl lab and there are really only 2 or 3 (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Mindstorms A/D, 8 bit or 10 ?
|
|
OK, I just got a Mindstorms this yesterday and I've been surfing the various web pages about it (Lots of good info!) and I came across something odd. The specs for the microprocessor say it has 8 bit A/D's (Analog to digital converters), but the raw (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Other LCDs
|
|
Drew I picked up a 20x4 LCD from B. G. Micro (see their on-line catalog at (URL) and view page 2 - the LCD is the one in the upper right at $8.95, part number LCD1002). For 2x16, it will work just plugging into the HB. I poked memory locations (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | IR Detection
|
|
Hi Everyone: I am trying out the infra red emission and detection with the Handy Board. I have succeeded in the emission part but the detection circuit is not working. I know that the emitter LED is fine , with the help of Radio Shack Infrared (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Controling LEGO trains via Decta Control Lab
|
|
(...) To change the speed of the pulsing, you change the frequency. Frequency is measured in Hz. You want more Hz. To change the speed of the train, you increase either the duty cycle or the voltage. The duty cycle is the percentage of time that the (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: CYBERMASTERS - how it works ?
|
|
Rene Virsik wrote in message ... (...) program (...) can (...) radio (...) Both. Pplease read yor answer in here. Eric (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Config Register error
|
|
When I download the pcode file using either HBDL or DL the pcode itself is loaded successfully but I then get an error from both programs saying the config register is set to 0xFF. I retried several times but the config register always reads 0xFF. I (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | IRDA and Handyboard?
|
|
Hi all, Electronics Goldmine has some notebook pc IRDA ports for $2! (URL) I think it would be Great to use a couple of these to get 2 Handyboards to talk with eachother. Or, get one handyboard to talk with my Notebook PC (which already has an IRDA (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Controling LEGO trains via Decta Control Lab
|
|
10Hz is nowhere near fast enough to control a train motor using PWM (pulse width modulation). You need at least 100Hz, and higher would be better. Any of your suggestions will vary the speed of a motor, but the most common is varying the duty cycle. (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|