 | | Re: The NXT bit of information...
|
|
(...) Ergh, Take a close look at some of the pictures to found online. The LED isn't IR, its a regular old red LED. JB (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) No, it's a regular part: (URL) exists 4L (URL) nuts: (URL) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) lego axle? (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) Indeed, see (URL) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) Not exactly. You can get a range of values out of a single RIS touch sensor by varying how hard you press on it... but it's a really small rnage of pressures over which it varies. Hook a touch sensor up to a port configured for a raw value, (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) Yes. The existing touch sensors are just switches--they give you on and off. Peter (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) ---...--- The 1400 mAh lithium battery more than replaces AA batteries that run down quickly and cost so much to replace it has a minimum capacity of 670% of 6 AA batteries ---...--- Rechargeable batteries are great, but what about capacity? (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) I am somewhat disappointed by the light sensor with its single IR LED. The "color" sensitivity hype made me think that at least 2 different color lightings were available. Of course the possibility of turning off the Led is a great (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) Yes, the article indicates the battery will be sold seperately (so it should be safe to get a retail set the moment they hit the shelves :) I was surprised at something in the article though - it says that both the existing touch sensors and (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) I'll be surprised if the rechargable battery isn't available as a separate item through LEGO Education. ROSCO (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: The NXT bit of information...
|
|
(...) According to that site: "Theres also an A/C plug in the battery to allow the NXT brick to run from a direct power supply when needed." That tells me, I'm gonna be buying the MINDSTORMS Education NXT instead of the retail one. (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | The NXT bit of information...
|
|
OK, yeah, that was a teaser. But in case you haven't, take a look at this LEGO site: (URL) a lot of interesting things here, in a very finished-looking form. Some strong hints on the motor encoders and how easy they are to use (but nothing (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | So its (MDP) over?
|
|
So is that it? All 100 are accounted for? (crosses fingers many potential participants were on vacation) -aps (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) I am entirely ignorant of helping kids, and have no idea if this is practical or reasonable (it probably isn't), but I'll mention my odd demo thought anyway... An exercise in understanding robots could be to pick a corridor with a corner in (...) (21 years ago, 23-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) This sounds like a good demo that someone within the MDP program can create (hint, hint, wink wink, nudge, nudge). Show the difference between navigating through a maze using (1) the 'dead reconing' method, (2) the ultrasound sensor and the (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
In lugnet.robotics, Justin Fisher wrote: <snip> (...) When I was a mentor for a local FLL team, I was so hard pressed to convince the kids that 'dead reconing' wasn't the way to go. THey had the entire program coded like 'go straight for 10 seconds, (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) I'd go further than that - I may be wrong here, but AFAIK professional roboticists largely consider dead reckoning to be a losing game, an amateur red-herring that you can waste all the time and money you want on and it will still never work (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) The question is just how much of this is handled at what level within the NXT firmware & software. I'd be surprised if LEGO doesn't do *something* with the built-in encoders - after all, *they* put them there. the question is how much. The (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) Tim, Just so you know, the people working on the NXT are aware of the problems people often have when trying to make a robot go straight, and they have addressed it. Some day, I'll show you the NXT program to accomplish that challenge. It will (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|
| |
 | | Re: turtle coding kit (Re: How would we (the rest of us) communicate ideas to the MDP?)
|
|
(...) Having given this a bit more thought, the code would be almost the same. Even though the encoders are built-in, there's no guarantee that the motors themselves are matched. You would still need control loops to ensure that the motors rotate at (...) (21 years ago, 22-Feb-06, to lugnet.robotics)
|