 | | mindscript - subroutines
|
|
Hi, I'm new to this mindscript stuff and lugnet, so hopefully someone can shed some insight for me. I was lead to believe that Mindscript had the capability of defining subroutines. In either Bricx or Scripted I keep coming up with an error when I (...) (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Square wheel vehicle update? Any success?
|
|
(...) Yep ! (2 URLs) (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Square wheel vehicle update? Any success?
|
|
Has anyone had any success (and online picture/video) with a Lego square wheel model? Thanks Bruce (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Re: 4x4 Buggy
|
|
(...) I had that doubt too, but don't you reckon that the distance between the right and the left wheels will help? The further away they are the slower and more powerful is the steering. Also, even if the RCX limits the current to each port, won't (...) (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Re: 4x4 Buggy
|
|
(...) Luca, Very nice drawing. To secure the RCX all you need is a couple beams that run along the bottom, and you can use a couple vertical beams (six stud long) to pin into the holes on the side of the RCX. (...) This may be a small problem, but (...) (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Re: 4x4 Buggy
|
|
(...) What do you exactly mean by this? (...) Because, since it's supposed to go on rough terrain, I'd like the electronics as far away from ground as possible to prevent any kind of damage. Reckon I'll have to buy extra universal joints (they are (...) (21 years ago, 22-Dec-05, to lugnet.robotics)
|
| |
 | | Re: 4x4 Buggy
|
|
Hello all, I've been reading this list for a while now, and this is my first response, if it comes through :) (...) Basically, the idea for your chassis is sound. However, there are a few improvements possible. You say you don't want to lower the (...) (21 years ago, 21-Dec-05, to lugnet.robotics)
|
| |
 | | Re: what batteries
|
|
(...) I mostly agree with your comparison. But NiMH has one major drawback: they power the RCX under 7.2V instead of 9V. The motors turn slower and deliver about half mechanical power, see this chart: (URL) Of course this is probably not a problem (...) (21 years ago, 21-Dec-05, to lugnet.robotics, FTX)
|
| |
 | | Re: what batteries
|
|
I've had very good luck using NiMH AA batteries in my RCX. I never ran a set of alkalines out in mine, so I cannot compare run times. However, a set of alkalines would need to last hundreds of times longer than a set of NiMH cells to be cheaper (not (...) (21 years ago, 21-Dec-05, to lugnet.robotics)
|
| |
 | | Re: 4x4 Buggy
|
|
(...) Sweet idea! I've been looking for a design that might work well outdoors, this could be the germ of it. (...) Looks like you need a superstructure of some kind. You can go up pretty high as long as you leave the RCX itself towards the bottom (...) (21 years ago, 21-Dec-05, to lugnet.robotics)
|
| |
 | | 4x4 Buggy
|
|
I've benn working on this ( (URL) ) 4x4 buggy with LDraw, but before buying the pieces I'm missing to actually build it I wanted to know if you had any ideas on how to brace the RCX to the robot's structure without lowering the ground clearance BTW (...) (21 years ago, 21-Dec-05, to lugnet.robotics)
|
| |
 | | what batteries
|
|
We are starting a mindstorm club at the missionary school here in Bogotá and have 4 sets, but we want to try to keep costs down so for the long term we were considering rechargeable batteries, but they have a significant voltage disadvantage. How (...) (21 years ago, 20-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Change of email address
|
|
(...) Plasticine extrusion? (21 years ago, 20-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Change of email address
|
|
(...) Merry C for you 2 too ;) (...) Try (URL) though it may not be approved immediately. ROSCO (21 years ago, 19-Dec-05, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Change of email address
|
|
(...) Ventilation? (21 years ago, 19-Dec-05, to lugnet.robotics)
|
| |
 | | Change of email address
|
|
Merry Christmas to everyone out there who knows what the holes in the beams are for ;) And everyone else too of course. Can't figure out how to change lugnet's idea of my email address yet, but barnes at sensors will cease to be in a few weeks time. (...) (21 years ago, 19-Dec-05, to lugnet.robotics, lugnet.technic)
|
| |
 | | Merry Christmas
|
|
Merry Christmas everyone and a happy new year! Thomas (21 years ago, 19-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
(...) (URL) has links to some pages which have ideas for connectors. Personally, I've had good luck with 4-40 machine screws, 3/4" long. As for the wire- you might take a sample with you to an electronics store (not Radio Shack- they probably don't (...) (21 years ago, 18-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
"Ken Koleda" <kkoleda@co.wayne.mi.us> wrote in message news:IrKM59.9vE@lugnet.com... (...) This may be of some use to make your own . (URL) (21 years ago, 18-Dec-05, to lugnet.robotics)
|
| |
 | | Re: ROBOLAB Update?
|
|
(...) There's a patch to update ROBOLAB 2.5.4 here: (URL) ROBOLAB 2.5.4 C Patch fixes a number of bugs in ROBOLAB 2.5.4. Once patched, users officially have ROBOLAB 2.5.4 C." CSSoh (21 years ago, 18-Dec-05, to lugnet.robotics)
|