 | | RCX firmware vs hardware
|
|
All, I've got an RCX 1.0, and my son has a 1.5. Is there anything that would cause problems if I loaded 1.5 firmware into a 1.0 RCX? While on the topic, what about 2.0 firmware in a 1.0 RCX? (22 years ago, 6-Jul-04, to lugnet.robotics)
|
| |
 | | Re: train control
|
|
Hi Daniel, (...) sorry to reply so late, I wanted to try it myself but didn't get around to do it yet (I'm starting an IT-Business as a consultant/systems programmer, see (URL) managed to run a train from an RCX with the standard power levels using (...) (22 years ago, 5-Jul-04, to lugnet.robotics.rcx.java)
|
| |
 | | Re: NQC problem...driving me insane!
|
|
(...) You should check to make sure your light sensor is in fact changing more than 5 counts. Start by changing the above code to 2 or 3. I don't recall with NQC, but with some languages (BrickOS) the values are backwards, so you may need to check (...) (22 years ago, 5-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
|
| |
 | | Re: Repairing small 9v battery box
|
|
(...) Hmmm, difficult. After a quick inspection, I'd say no. (...) What batteries are you using? I doubt there's many 9V batteries that can take sustained 5A for very long. ROSCO (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Re: NQC problem...driving me insane!
|
|
(...) Well, actually, that code works fine (running MacNQC, a fairly recent version, with 2.0 firmware). One thing to check, code-wise, is to display SENSOR_1 on the LCD, and see what the numbers are (is it set to raw mode? Is the sensor bad (I've (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
|
| |
 | | NQC problem...driving me insane!
|
|
Hey all, I know I must be doing something very simple wrong here - but I can't for the life of me figure it out. What I'm trying to do: Have a light sensor pointed at a surface. Pass that value off to a variable (the variable then contains the (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
|
| |
 | | Re: Repairing small 9v battery box
|
|
(...) I had a large battery box that was did not work reliably (sometimes yes, sometimes no). The problem was burning at a battery contact. The current does not need to be very high to do that if the contact area is very small. The discolored spots (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Repairing small 9v battery box
|
|
I've got one recently off od Bricklink, and it seems not to be working. Yes, new battery, yes, battery works in other small 9v boxes, yes, I made sure it was cool (thermal protection). Any ideas? Any suggestions how to troubleshoot or fix it, (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: train control
|
|
(...) There is a fundamental difference between the RCX and a Lego Train controller - the controller uses smooth power from a 3-pin regulator, with the voltage varied using a chain of resistors. The RCX uses PWM power with approximately 166ms square (...) (22 years ago, 3-Jul-04, to lugnet.robotics.rcx.java)
|
| |
 | | Re: how to program the spybot remote
|
|
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | how to program the spybot remote
|
|
hi everybody ;-) I use brickCC to program my spybot, do you know how I can program remote' s functions ?? (I talk about the spybot's remote) I' m not a programmer specialist so could you give me few code or a good explanation Thanks to all Chris (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Instructions for building a diode-based limit switch can be found at (URL) also has a limit switch adapter, that lets you use standard Lego switch sensors to stop a motor without using any sensor ports. (22 years ago, 1-Jul-04, to lugnet.robotics)
|
| |
 | | Re: phantom.dll control problem
|
|
----- Original Message ----- From: "Ayse Gaye Soykok" <asoykok@e-kolay.net> <snip> (...) mfc (...) be (...) CreateFile(USB_TOWER, (...) I was able to make it work using precisely this call ... got the basic working VC++ version from here: (URL) I (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: phantom.dll control problem
|
|
(...) Hi, I'd like to say "yes this is the problem, how I' ve forgotten" but firmware is downloaded. Test program works but mine does not. I am using the appropraite commands I am sure. Can it be a problem about the aplication? Test program is VB. (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: phantom.dll control problem
|
|
Silly question, but - does your RCX have firmware downloaded to it? Rob "Ayse Gaye Soykok" <asoykok@e-kolay.net> wrote in message news:Hzxw7s.1123@lugnet.com... (...) I am (...) controls, in (...) the rcx (...) program(downloaded with (...) may (...) (22 years ago, 28-Jun-04, to lugnet.robotics.rcx)
|