 | | NQC problem...driving me insane!
|
|
Hey all, I know I must be doing something very simple wrong here - but I can't for the life of me figure it out. What I'm trying to do: Have a light sensor pointed at a surface. Pass that value off to a variable (the variable then contains the (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
|
| |
 | | Re: Repairing small 9v battery box
|
|
(...) I had a large battery box that was did not work reliably (sometimes yes, sometimes no). The problem was burning at a battery contact. The current does not need to be very high to do that if the contact area is very small. The discolored spots (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Repairing small 9v battery box
|
|
I've got one recently off od Bricklink, and it seems not to be working. Yes, new battery, yes, battery works in other small 9v boxes, yes, I made sure it was cool (thermal protection). Any ideas? Any suggestions how to troubleshoot or fix it, (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: train control
|
|
(...) There is a fundamental difference between the RCX and a Lego Train controller - the controller uses smooth power from a 3-pin regulator, with the voltage varied using a chain of resistors. The RCX uses PWM power with approximately 166ms square (...) (22 years ago, 3-Jul-04, to lugnet.robotics.rcx.java)
|
| |
 | | Re: how to program the spybot remote
|
|
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: how to program the spybot remote
|
|
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | how to program the spybot remote
|
|
hi everybody ;-) I use brickCC to program my spybot, do you know how I can program remote' s functions ?? (I talk about the spybot's remote) I' m not a programmer specialist so could you give me few code or a good explanation Thanks to all Chris (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Instructions for building a diode-based limit switch can be found at (URL) also has a limit switch adapter, that lets you use standard Lego switch sensors to stop a motor without using any sensor ports. (22 years ago, 1-Jul-04, to lugnet.robotics)
|
| |
 | | Re: phantom.dll control problem
|
|
----- Original Message ----- From: "Ayse Gaye Soykok" <asoykok@e-kolay.net> <snip> (...) mfc (...) be (...) CreateFile(USB_TOWER, (...) I was able to make it work using precisely this call ... got the basic working VC++ version from here: (URL) I (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: phantom.dll control problem
|
|
(...) Hi, I'd like to say "yes this is the problem, how I' ve forgotten" but firmware is downloaded. Test program works but mine does not. I am using the appropraite commands I am sure. Can it be a problem about the aplication? Test program is VB. (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: phantom.dll control problem
|
|
Silly question, but - does your RCX have firmware downloaded to it? Rob "Ayse Gaye Soykok" <asoykok@e-kolay.net> wrote in message news:Hzxw7s.1123@lugnet.com... (...) I am (...) controls, in (...) the rcx (...) program(downloaded with (...) may (...) (22 years ago, 28-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | phantom.dll control problem
|
|
Hi all, I am going to use phantom.dll controls(I hope)for communicating with rcx. I am using visual C++ 6.0 as the development environemnt. I am using the controls, in a win32 console application. The problem is nothing seems to be send to the rcx (...) (22 years ago, 26-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) Thanks Jerry, In fact Ultimate ROBOLAB programs are "firmwares". You can design simple programs or even complex ones controlling advanced robots. You also can use the software to write a complete firmware as a state machine controlling the RCX (...) (22 years ago, 28-Jun-04, to lugnet.robotics)
|
| |
 | | Re: BrickFest is coming, and so are the robots!
|
|
(...) The reason behind that is pretty simple. It's because I've entered many of the challenges. I've seen what other people out there can do, and I'm just lucky they haven't been entering. I was just looking over the rules, and (as usual) John's (...) (22 years ago, 28-Jun-04, to lugnet.events.brickfest, lugnet.technic, lugnet.robotics)
|
| |
 | | train control
|
|
hi I want to use rcx to control a lego train, but the fact that lejos only have 7 levels makes it dificult to set the speed. Jürgen Stube wrote in september2001: "Yes, the standard LEGO routines make it very hard to control speed. Basically with an (...) (22 years ago, 28-Jun-04, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) exciting, but I am a bit confused about what it is. It's a programming tool (piece of software) that creates 'assembler programs' which are downloaded to the RCX in the same way as you download firmware. Each one allows the RCX to be used to (...) (22 years ago, 26-Jun-04, to lugnet.robotics)
|