 | | brickos with suse 9.1
|
|
I'm tying to get brickOS started on a Suse 9 System, Did anybody install brickOS and the gcc-hitachi on Suse 9 System? After I download the brick.srec to the RCX it crashes. thx KHL (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: table brickos light to percent
|
|
In my opinion, the best way to approach this is the following: When the program starts, begin a Calibration, by first activating the light sensor, then reading the value. You can either wait a specific amount of time or have the user press a button (...) (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: table brickos light to percent
|
|
(...) Hi Thomas, Here's the formula used in the dsensor.h include file: #define ds_scale(x) ((unsigned int)(x)>>6) //!< mask off bottom 6 bits #define LIGHT(a) (147 - ds_scale(a)/7) //!< map light sensor to 0..LIGHT_MAX This maps the raw sensor (...) (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | table brickos light to percent
|
|
i there a table or converter from brickos light readings to light percentage ( and vice versa ) Thomas (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) A little off topic for this thread, but I thought it was worth mentioning: The microscout can be controlled by a spybot as well. The spybot has both IR comms and VLL I/O. So a spybot has two built in motors and can control a microscout for a (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
Basicly, you can use the Microscout as an extra motor (but of course you're blowing away a motor port to do it! The ms_Fwd and ms_Rwd commands have an unavoidable delay in between them, so you can't get the motor to run continuously (not that I'm (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | IR Range Finders on CyberMaster
|
|
If anyone is interested, it is possible to use the MindSensors separately powered SHarp GPD12 IR range finders on the CyberMaster. These range finders require a motor port to power them, and also connect to sensor port. Connecting them to the (...) (22 years ago, 26-May-04, to lugnet.robotics.cybermaster)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) Hi Mark, here's a program in Mindscript for your RCX that will exercise the Microscout a bit: program RCX2MS { #include"rcx2.h" #include"rcx2vll.h" main { vll_begin(B) forever { ms_Fwd(B) ms_Fwd(B) ms_Fwd(B) ms_Rwd(B) wait 200 // 2 seconds } } (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) No - they can't. They use visible light - not IR. (...) Nothing interesting! (...) 'P' mode is how you program them - but not from the RCX. (...) Yes - you can use the USB tower - it has both a visible light AND an IR light. But the older (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
Here are a couple answers for you... (...) I THINK you can program a Micro Scout using the USB tower. The 1.5 & 2.0 sets come with a fiber-optic cable that you can use. (...) Here's a page with more info about VLL (URL) (...) Hope that helps Steve (22 years ago, 25-May-04, to lugnet.robotics)
|
| |
 | | RCX and Micro Scout Communication
|
|
I have an RCX 1.0, which I program in Visual Basic, and a couple of Micro Scouts from the DDK and DSDK. Can the Micro Scouts understand RCX IR messages and if so what do they do in response? Is the "P" mode of the Micro Scouts the way to program (...) (22 years ago, 25-May-04, to lugnet.robotics)
|
| |
 | | Re: Is there any use for Spybotics
|
|
(...) Oh, is your robotics world about to open up, hehehe... (...) Oh yes. Steve will probably post more details, but search back through the Lugnet archives. The RCX can control the manas units via IR, and the Spybots can handle VLL ass well as (...) (22 years ago, 25-May-04, to lugnet.robotics)
|
| |
 | | Is there any use for Spybotics
|
|
Hello all, I own a scout and micro scout and for my graduation I will be getting an RCX. I purchased a plain IR Tower and downloaded a document off the lego homepage and programmed my Scout from the computer, and program my Micro Scout through my (...) (22 years ago, 25-May-04, to lugnet.robotics.spybotics)
|
| |
 | | Space Elevevator design studies using Mindstorms
|
|
I found this while nosing around (URL) lifters go up and down simulated carbon nanotube ribbons. Hope you find it interesting. (22 years ago, 24-May-04, to lugnet.mediawatch, lugnet.technic, lugnet.robotics)
|
| |
 | | Re: issues with 6-legs bot
|
|
(...) Your approach is pretty common. As it turns out, you can (should) remove the wait time, also. Many people think they need to tell the robot how long to turn, or how long to go forward. It's like driving down the road in a car. You don't look (...) (22 years ago, 20-May-04, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
| |
 | | RE: issues with 6-legs bot
|
|
Hi Steve, Thank you very much for your put! (...) Can't take the credit. I got the idea from the Sato book, instead of 4 legs, I thought the 6 legs are much more stable. (...) That's pretty much what I did initially, except I used to put in "wait" (...) (22 years ago, 20-May-04, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
| |
 | | Re: issues with 6-legs bot
|
|
What if you were to make a small platform for the light sensors in between the legs that rest on the ground and has a slide somewhere so when the robot moves up or down it stays touching the ground. ----- Original Message ----- From: "Elizabeth (...) (22 years ago, 20-May-04, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
| |
 | | How to increase address range in brickos ?
|
|
Does anyone know a way to increase the address range in brickos beyond 0 through 15 ? When I cycle through the address range via View + Prgm it stops at 0xF0. The port is always set at zero. What if I modify the port value ? Or does that affect (...) (22 years ago, 19-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: issues with 6-legs bot
|
|
(...) Am I correct in thinking the two front, and two back legs don't move, only the middle two? That's a nice, simple design. And you have two light sensors, and your goal is to keep them on either side of the line, right? (...) If I understand (...) (22 years ago, 19-May-04, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
| |
 | | issues with 6-legs bot
|
|
Hi, I built this 6-legs bug for a black line tracking test. The construction: It is a walker with 2 motors, one for 3-left-legs, another one for the right. Middle leg on each side is connected on an 8-tooth gear and attach an 40-tooth gear. This (...) (22 years ago, 19-May-04, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|