 | | Re: DCC for the RCX
|
|
(...) I'm no electronics engineer by any stretch-- A diode, iirc, allows DC current to 'flow thru' in only one direction. What would a diode do across the output on the top of the train motor? And why would one be good for 'inductive' loads such as (...) (23 years ago, 29-May-03, to lugnet.robotics.rcx, lugnet.trains)
|
| |
 | | Re: Help with BricxCC and NQC...
|
|
(...) Hello Shawn, Event support appeared only with RCX firmware version 2.0. To be able to use them, you must - Download firmware version 2.0 in your RCX brick - Check RCX2 radio box on BricxCC opening screen Cheers Philo www.philohome.com (23 years ago, 29-May-03, to lugnet.robotics)
|
| |
 | | Help with BricxCC and NQC...
|
|
Hello. I have joined the list to hopefully work through some issues I am having programming my RCX, gather more info about robotics, and possibly offer some help in time. Please let me know if this is not the best list to be posting this sort of (...) (23 years ago, 29-May-03, to lugnet.robotics)
|
| |
 | | Re: DCC for the RCX
|
|
(...) I don't install them either, and I have done something like 30 motors so far. (...) True, but ONLY if you are just going to use the RCX as a output. You can dial the voltage that DB100's (and most other Digitrax) boosters put out to a exact (...) (23 years ago, 29-May-03, to lugnet.robotics.rcx, lugnet.trains)
|
| |
 | | Re: need help for MLCAD:"add new piece to library"
|
|
(...) Chris, I thought that pneumatics parts had made it into the official parts release. When was the last time you updated your parts? I've been known to use parts from here: (URL) I prefer the parts made by JP Brown. You can get them off my (...) (23 years ago, 29-May-03, to lugnet.robotics.rcx)
|
| |
 | | Re: DCC for the RCX
|
|
(...) output? Dave, I used a 1N4002. It's a fairly common 1 amp switching diode. Here's a picture from my latest decoder install: (URL) that the banded end of the diode gets the blue lead from the decoder. The unbanded end gets the white lead. If (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
|
| |
 | | Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
|
|
(...) Yes - but that is precisely 100% of the problem. There is no known convenient/cheap GPS-like system with the properties we desire. Camera's above the arena and things pasted onto the floor are not possible in many real-world situations. The (...) (23 years ago, 28-May-03, to lugnet.robotics)
|
| |
 | | Re: DCC for the RCX
|
|
In lugnet.robotics.rcx, Mark Riley wrote: <snip> (...) Mucho appreciated Mark. The Diode--any diode will do? and just solder it across the connector output? Take care, Dave (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
|
| |
 | | Re: DCC for the RCX
|
|
(...) I (...) resistors (...) goes (...) run (...) the (...) isn't (...) reduce the (...) David, When I installed my first decoders (Digitrax DN121), I omitted the capacitors, figuring if the buzzing was annoying, I could always add them later. As (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
|
| |
 | | Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
|
|
(...) items (...) the (...) (that (...) Even commercial guidence systems use periodic recalibration, for example with small magnets in the floor. The robot knows where the magnets are and if it finds a magnet off center to it's expected position it (...) (23 years ago, 28-May-03, to lugnet.robotics)
|