To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *36194 (-20)
  Re: Land mine robot
 
(...) Since this is a school project - we shouldn't be telling you how to do it, we should be pointing you towards ways to search for a solution yourself. So... This requires a logical approach (and that always looks good in a school report!) Now - (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
 
  Re: Land mine robot
 
I'm a Senior in high school and one of the requirements to graduate is that we must complete a Senior project. I know nothing about building sensors or electronics at all. All though I could learn very easily. The purpose of the post was to find (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
 
  Re: Land mine robot
 
(...) I've been using mine in sand, dirt, middle of the street, etc. for years and haven't had any serious problem. Just be sure to clean everything when you're done. Warm water and gentle dish detergent is what I suggest (don't do the motors (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
 
  Re: Hi, I'm new
 
"Tjandra J" <lego-robotics@crynwr.com> wrote in message news:046601c2bad2$44...Tjandra... (...) with (...) Check out this site. Look in the "Gallery" (URL) walkers are a real challenge. Good luck with your project. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: RCX Motor Controller
 
"Carson Au" <carsonau@excite.com> wrote in message news:H8oBI4.7o2@lugnet.com... (...) The RCX uses Pulse Width Modulation to control the motors. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: Hi, I'm new
 
Tjandra, you have posted your message inside a thread with a different topic. You may run the risk of your message never being read. Use the "New" icon at the top right to start your own thread, and try typing in the title exactly what you're asking (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: New Parts
 
I liked the "Technic Connector Toggle Joint Smooth, Part #44 ". As for the escapement wheel, "bah!" :P (24 years ago, 13-Jan-03, to lugnet.technic, lugnet.robotics, lugnet.modelteam)
 
  RCX Motor Controller
 
Hi to all, How does the RCX control the lego motor's? Using what? Some basic facts forward - forward current backward - backward current Float - contacts opened Stop - contacts shorted carson (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: I2C device for the RCX
 
"Bastiaan v.Kesteren" <b.van.kesteren53@zonnet.nl> wrote in message news:H8nvnF.2rz@lugnet.com... (...) takes (...) package, (...) A 3% error rates (7 out of 250 messages) is far too high. I would have expected error rates under 1 in 10 million (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: I2C device for the RCX
 
"Bastiaan v.kesteren" <b.van.kesteren53@zonnet.nl> wrote in message news:H8o02v.Gpz@lugnet.com... (...) 375ms, which is (...) at the sensor (...) 6360Hz. (...) I don't understand your references to clock pulses. The I2C protocol is edge triggered (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: I2C device for the RCX
 
ARGH!!!...!!! i'm getting nuts of all these numbers! Now it appears that my stopwatch didn't give the time in steps from 1 ms, but in steps from 10 ms so then the program takes 3750ms, which means 70,6 packages per second. the RCX has send 1 adress (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  RE: Communicating to RCX with Notebook Infrared Port
 
The notebook IR ports are IrDA ports. This is the only program I've ever found that will use a notebook IrDA port for controlling Consumer IR devices: (URL) IR is similar to what is used by the RCX. (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Communicating to RCX with Notebook Infrared Port
 
Hi everybody there, I'd like to use my notebook's IR port to talk to the RCX. Can anybody tell how I can do that? Thanks for our help! Wolfgang (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  New Parts
 
Rather than update the old "Part Of The Week" feature every week, I've decided to periodically update a list of new parts. I've put this on the old PotW page: (URL) you've seen any new parts that should be included, please let me know! thanks, TJ (24 years ago, 13-Jan-03, to lugnet.technic, lugnet.robotics, lugnet.modelteam)
 
  Re: I2C device for the RCX
 
(...) Nope, I didn't. Mixed up the packages/sec and bits/sec. It should be 6360Hz. Sounds even more faster (-: (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  DJGPP Cross Compiler Progress
 
I have successfully built an h8300 cross compiler for DJGPP using the newest version of gcc 3.2. I was not successful using gcc 2.95.2, the current used gcc compiler with brickOS, and at the advice of others tried gcc 3.2. Since it is the goal of (...) (24 years ago, 13-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: Land mine robot
 
(...) I specified underneath to make it unlikely that the robot would detect them by either optical means (because I assumed that the challenge was for a non-visual method), and to prevent any cheating by a team using some form of IR flash to inform (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: I2C device for the RCX
 
Before starting the hacking,I did some tests whit this 'for-lus-delay', and I found the results better than expected. I found that this: for(long i=0;i<100000;i++); takes about 120ms, so one for lus takes 0.0012ms. I made a test program which first (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
 
  Re: Spybots missoins (was Re: Packaging!)
 
(...) Mark is correct. I would be happy to begin a Spybotics Mission Trading Area on BimP. I am a fan and would love to see what types of missions could be created by the community. To begin, I think we need to provide mission objectives, mission (...) (24 years ago, 13-Jan-03, to lugnet.robotics.spybotics, lugnet.lego)
 
  Re: Land mine robot
 
(...) Why underneath? A flat surface with paper discs taped down to represent mines would be fine. Then the light sensor could be used to detect them. After all, the point is really to find them without rolling over any while searching. You'd need (...) (24 years ago, 13-Jan-03, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR