 | | Re: Firmware download troubles
|
|
(...) The problem he's describing, if it's the same one I have, is independant of the position, direction, and power level of the tower. It seems to have something to do with BrixCC itself. The only thing I find puzzling is that Matt (the other Matt (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: BrickOS Threading...
|
|
Steve, I checked in some changes this morning (into cvs) to put the motor controller back at the 1 ms interval. However, I want to complete the get_sys_time() updates that Mark Riley has proposed; so that can be tested as well. I am not sure when (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Firmware download troubles
|
|
(...) It's funny that you should bring this up - I've had exactly the same problems with several RCX's and downloading firmware from BrixCC. The only solution I've been able to find is to download the firmware using the RIS2.0 software and then (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: sys_time (long post)
|
|
(...) It turns out that the nature of the glitch depends on the order you read the upper and lower 16-bits of sys_time. If the compiler generates code that reads the high word first (which it seems to do), then your example will work. However, if (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Fw: [handyboard] xmas songs
|
|
----- Original Message ----- From: <x01101001@yahoo.com> To: <handyboard@yahoogroups.com> Sent: Friday, December 13, 2002 8:19 PM Subject: [handyboard] xmas songs (...) (24 years ago, 13-Dec-02, to lugnet.robotics.handyboard)
|
| |
 | | Re: Working motorized focus for Vision Command
|
|
I was wondering if anybody would improve the power focus for the Lego camera. You have accomplished this very well. I especially like your tilt drive. Sticking that 40 tooth gear without glue is super. Congratulations! Bob Fay (URL) Haye" (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | Re: BrickOS Threading...
|
|
(...) In trying to balance an RCX on two wheels, every little bit makes a difference. I didn't think it would matter quite that much, but my robot really shakes more with the new version. Thanks for the work, Steve (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Hammer Help
|
|
winding and unwinding string seems to be to slow if i understand it good so my idea is here: use two wheels (pulleys) especiali as big as you can put into your design they should be with flat surface so it meand they should be from old sets like: (...) (24 years ago, 13-Dec-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Hammer Help
|
|
Roy I thought about designing such a thing a while ago. My decision was that I'd make something like a Roman ballista. I'd wind up a string on a winch to cock the hammer then unwind the string all the way back again. The catch would be released by (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | setjmp/longjmp for brickOS
|
|
Hi all, I am currently attending to a lecture in real time system on my university and we were assigned the homework to do exception handling in C on the RCX using setjmp and longjmp. Of course those are not available in brickOS so that task (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|