 | | Re: Ultrasonic Sensor
|
|
Hello All, Many thanks to all who replied to my original post on this topic. The hardware is build (and works - sometimes(!!!)) and I am now writing the thesis for the project. It is due for submission next week, and if anyone would be interested in (...) (25 years ago, 12-Apr-02, to lugnet.robotics)
|
| |
 | | RCX Firmware speed versus legOS
|
|
The discussion about the Firmware speed is intresting indeed. So I did a fast, by no means representative, reserch. The following program is a legOS program reading the light sensor, calculating some values and printing the elapsed time: ---...--- (...) (25 years ago, 11-Apr-02, to lugnet.robotics)
|
| |
 | | Re: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
For the Workshop3D Event I use the following construct, the button handling is from the book "Extreme Mindstorms": : main ( -- ) \ Main Task init \ do main initialize ( ... ) BEGIN ( ... ) BUTTON_SCAN BUTTON_RUN? IF ( ... ) \ Calibrating BEGIN ( ... (...) (25 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
 | | RE: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
I need to look at some items for Joerg, but I'll also look at a small supervisor that integrates the View,Run,Prgm,and On/Off buttons. This hsould be pretty easy and would be a good bit of example code. Cheers, Ralph (25 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
 | | Re: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
(...) off (...) True. But I find not very practical to be forced to use the terminal to switch off the RCX or start the program again, expecially when you are attending a contest or take your robot to an exhibit. What I meant by "supervisor" is some (...) (25 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
 | | Two RCX with one IR-Tower
|
|
Hello, I want to control two RCX with one ir-tower. The problem is that the RCX should send back status information. Sending information to the RCX is quite easy: Both RCX receive the message but only one will perform the command. I found (...) (25 years ago, 11-Apr-02, to lugnet.robotics.rcx)
|
| |
 | | Re: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
(...) If you have the new version 2.1 the POWER-OFF word via terminal to shut off and the red button to power on works fine. If you have an earlier version (1.2x) you have to use the words RCX_INIT and POWER_INIT to initialize the brick and the (...) (25 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
 | | Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
Mario, i'm interested in pbForth example scripts, too. Furthermore, the "supervisor" you suggested could be the answer to one of my questions in (URL) concerning turning the RCX off and on without loosing pbForth: 2) According to Knudsen, i have to (...) (25 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
 | | LEGO Satellite Uplink
|
|
Imagine what happens when a TV truck pulls up to a crime scene and the technician has to establish a Satellite Uplink for his live news feed. My latest project is a LEGO Dish that is motor driven, both in azimuth and elevation. It scans back and (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
|
| |
 | | Interesting robotics article at Wired.
|
|
Hey folks, Just read this and thought it was interesting enough to pass on. Not exactly Lego related but it might give some people ideas on directions to build in. (URL) Baydar bbaydar@hfx.eastlink.ca (25 years ago, 10-Apr-02, to lugnet.robotics)
|