 | | Re: Mechanical tricks
|
|
Try driving a gear off-center (ie put the drive axle of the motor into one of the other holes in the gear). This may not give you exactly the behaviour you want though. (...) (25 years ago, 2-Nov-01, to lugnet.technic, lugnet.robotics)
|
| |
 | | RE: Using IR Remote within pbFORTH
|
|
(...) If Caldera OpenDos supports QBASIC, then there is a program out there. I'll email it to you separately. (...) This can be awkward, because pbForth is expecting communications at 2400,n,8,1 while the remote is at 2400,o,8,1 You can call a (...) (25 years ago, 2-Nov-01, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: A job involving LEGO Mindstorms!
|
|
Good for you!!! I always knew you did'nt like some Technic stuff not to mention Mindstorms. For me making Mechanical things is great but can be sorta dull sometimes , well at least until you can see the results, what I like most is once the tedious (...) (25 years ago, 31-Oct-01, to lugnet.robotics)
|
| |
 | | Re: Mechanical tricks
|
|
(...) The obvious answer would be to take (say) a 40t gear wheel and file off half of the teeth. Put that on your input shaft and a regular 40t gear on the output shaft and it will rotate for half of a revolution of the input and stay still for the (...) (25 years ago, 2-Nov-01, to lugnet.robotics)
|
| |
 | | Re: Using IR Remote within pbFORTH
|
|
(...) Interesting. What sort of class/project is this? (...) I think I have some DOS dowload program at home. I never tried it, so I can't tell you whether it really works. I got it from the internet, so I suggest you try some search engines. If you (...) (25 years ago, 2-Nov-01, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Using IR Remote within pbFORTH
|
|
I'm trying to work a project for class using a Mindstorms kit. I want to program the system using Forth, but I've had two minor glitches. 1) Is it possible to download the firmware from an old DOS system? I've had no problem using NQC, but the (...) (25 years ago, 1-Nov-01, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Mechanical tricks
|
|
Hello, I'm looking for a mechanical (non-robotic) solution to a technic problem I'm facing. (I crossposted to robotics, cause you guys think about gears all the time, too. Plus, you're really smart and stuff.) My input is a constantly rotating (...) (25 years ago, 2-Nov-01, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MIndstorms Neural Network in Java
|
|
(...) Neural nets use a LOT of CPU time - you might want to consider using C code with LegOS - it's quite a bit faster than Java. What kind of application did you have in mind? ---...--- Steve Baker ---...--- Mail : <sjbaker1@airmail.net> WorkMail: (...) (25 years ago, 2-Nov-01, to lugnet.robotics)
|
| |
 | | Re: Mindstorms Automatic Train Control Questions
|
|
You can use micro-scout to control switch point, connected by fibre cable with a scout. I tested it, no problem, so that you can use two outpput ports on scout to control tracks. Zhengrong ---...--- (...) (25 years ago, 2-Nov-01, to lugnet.robotics)
|
| |
 | | Re: Mindstorms Automatic Train Control Questions
|
|
(...) Could a micro scout be used to manipulate switch points ? Might be an interesting use for the micro scout. Will it respond to the handheld IR remote control ? Is there any way to make it address selectable ? Hmmmmmm, there still may be a few (...) (25 years ago, 2-Nov-01, to lugnet.robotics)
|